Bedienungsanleitung 3Dprintingsystems UP Plus (Seite 20 von 56) (Englisch)

534678

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

UP Plus

3D Printer User Manual

3.1.6 Setting the

platform

This section is pro

bably the most important of the entire manual

Please read it carefully to ensure that you understand the

vital for

successful 3D printing.

To print successfully, the

platform

folded over) from the nozzle. As each printer is slightly different, this distance needs to be cal

brated before starting to print.

To work

out the correct nozzle distance, please follow th

Click “3D Print” and click

“Maint

Windows version

In the text box, type in the height to which you want the

platform

to move to, and click the “To” button. In the

above example, the

platform

UP Plus

has a print height of 1

Check the distance between the nozzle and the

If, for example, the

platform

away from the nozzle, increase the number

click the “To” button.

As the

nozzle

start increasing the number in the text box by

0.2

mm increments and click the “To” button. Repea

until you get to within 0.2mm of the nozzle.

way to check the distance between the nozzle and

form

is to fold a piece of paper in two (Which will make

it about 0.2mm thick) and use that as a spacer to gauge

the distance between the

nozzle and

Now click “Set to Nozzle Height”.

Troubleshooting

3D Printer User Manual

v 2013.6.10

platform

Height

bably the most important of the entire manual

and only needs to be done seldom

Please read it carefully to ensure that you understand the

platform

height setup procedure, as it is

successful 3D printing.

platform

should be set to start at a distance of 0.2mm (A piece of paper

folded over) from the nozzle. As each printer is slightly different, this distance needs to be cal

brated before starting to print.

out the correct nozzle distance, please follow th

ese steps:

“Maint

enance”, the below dialogue box will open.

MAC version

In the text box, type in the height to which you want the

to move to, and click the “To” button. In the

platform

will move to 134mm. The

has a print height of 1

35 to 138mm.

Note: You do not want to crash the

the nozzle, so increase the height in smaller and

smaller increments as you get closer to the

nozzle. If you do crash the

nozzle, it is best to

initialis

Check the distance between the nozzle and the

platform.

platform

appears to be about 2mm

away from the nozzle, increase the number

by 1mm and

As the

platform gets closer to the

start increasing the number in the text box by

mm increments and click the “To” button. Repea

t this

until you get to within 0.2mm of the nozzle.

TIP: An easy

way to check the distance between the nozzle and

plat-

is to fold a piece of paper in two (Which will make

it about 0.2mm thick) and use that as a spacer to gauge

nozzle and

platform.

TIP:

If you find you get lifting at a later

stage, increase the

platform

Now click “Set to Nozzle Height”.

Troubleshooting

and only needs to be done seldom

height setup procedure, as it is

should be set to start at a distance of 0.2mm (A piece of paper

folded over) from the nozzle. As each printer is slightly different, this distance needs to be cal

Note: You do not want to crash the

platform into

the nozzle, so increase the height in smaller and

smaller increments as you get closer to the

nozzle. If you do crash the

platform into the

initialis

e again.

If you find you get lifting at a later

platform

height.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

3Dprintingsystems UP Plus Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info