Bedienungsanleitung 3Dprintingsystems UP Plus (Seite 35 von 56) (Englisch)

534678

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

UP Plus

3D Printer User Manual

Base Height:

This is the thickness of the raft of material before the support layer is pri

the printer starts printing, it first prints a raft of non

material are horizontal (along the Y axis). It keeps building up horizontal rows of support material

for as many mm as you

have chosen. Then, just before it gets to the bottom surface of the real part, it

starts to build support layers perpendicular to the raft layers layer.

Part - Angle:

The part Angle determines at what point solid (dense) support

material gets used. If the angle is small than the printer will add

solid fill layers under the part surface. The thickness of this

solid (dense) support is determined by the “dense” parameter

nder the Support options as described below.

Part - Surface:

This parameter determines how many layers form the bottom face of a part when it is not solid.

For example, if you set it to 3, the machine will print 3 complete layers before going into

non-s

olid mode. This does not, however, affect the side wall thickness on non

are all the same thickness (approximately 1.5mm) irrespective of the fill mode.

Stable Support

: Stable support creates support that is more rigid and the model is

distort, but the support material is more difficult to remove.

Shell:

By selecting this mode, the software will not create the internal honeycomb fill and will

only create an external shell. For example printing the bunny with this selecte

bunny, saving material however making it fragile. The shell option does not work well for parts

with flat surface tops, e.g. a cube as there is nothing to support the top surface.

4. Printing

One of the keys to successful printing on

parts, there is a tendency for the edges of the part to lift

Recommendations for printing large parts:

•

Preheat the platform for 30mins

• Keep printer

extruder

•

Ensure the distance between the nozzle and platform is close enough

• Check nozzle

distance to each corner of the platform.

•

It also helps to run the printer in a room that

and free of drafts.)

Troubleshooting

3D Printer User Manual

v 2013.6.10

This is the thickness of the raft of material before the support layer is pri

nted under the part. When

the printer starts printing, it first prints a raft of non

solid material in which all the lines of support

material are horizontal (along the Y axis). It keeps building up horizontal rows of support material

have chosen. Then, just before it gets to the bottom surface of the real part, it

starts to build support layers perpendicular to the raft layers layer.

The default value

The part Angle determines at what point solid (dense) support

material gets used. If the angle is small than the printer will add

solid fill layers under the part surface. The thickness of this

solid (dense) support is determined by the “dense” parameter

nder the Support options as described below.

This parameter determines how many layers form the bottom face of a part when it is not solid.

For example, if you set it to 3, the machine will print 3 complete layers before going into

olid mode. This does not, however, affect the side wall thickness on non

solid parts, which

are all the same thickness (approximately 1.5mm) irrespective of the fill mode.

: Stable support creates support that is more rigid and the model is

distort, but the support material is more difficult to remove.

By selecting this mode, the software will not create the internal honeycomb fill and will

only create an external shell. For example printing the bunny with this selecte

d will print a hollow

bunny, saving material however making it fragile. The shell option does not work well for parts

with flat surface tops, e.g. a cube as there is nothing to support the top surface.

One of the keys to successful printing on

the UP

is platform preheating. Particularly with large

parts, there is a tendency for the edges of the part to lift

up from the platform.

Recommendations for printing large parts:

Preheat the platform for 30mins

– In “Maintenance” click “Platform

preheat 1 hour”

extruder

door closed during preheating and printing.

Ensure the distance between the nozzle and platform is close enough

distance to each corner of the platform.

It also helps to run the printer in a room that

is not too cold (i.e.

warmer than, say, 18

Troubleshooting

nted under the part. When

solid material in which all the lines of support

material are horizontal (along the Y axis). It keeps building up horizontal rows of support material

have chosen. Then, just before it gets to the bottom surface of the real part, it

The default value

is 2mm.

This parameter determines how many layers form the bottom face of a part when it is not solid.

For example, if you set it to 3, the machine will print 3 complete layers before going into

solid parts, which

: Stable support creates support that is more rigid and the model is

less likely to

By selecting this mode, the software will not create the internal honeycomb fill and will

d will print a hollow

bunny, saving material however making it fragile. The shell option does not work well for parts

is platform preheating. Particularly with large

preheat 1 hour”

warmer than, say, 18

°C

3Dprintingsystems UP Plus Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info