534678

3Dprintingsystems UP Plus Seite 48

48
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
UP Plus
3D Printer User Manual
9.
The platform rests on a tripod (three
spru
ng screws) and in order to level it
tighten or loosen
each of the three screws
until the distance between the nozzle a
the platform is equal
at each corner.
10.
As the platform gets more level, increase
the platform
height to the nozzle, so it is
easier see the gap.
You will most likely need to repeat the process 5
a few times
going in a clockwise manner. Each
time r
educing the amount of turn on the screws.
Loosen a screw and the related corner of platform will rise. Tighten, or loosen, the screws until
you have the same gap between the nozzle and the platform at all four corners of platform.
7.0.
Tips & Tricks
parts
When printing with ABS Plastic
the nozzle at 260c
it comes out in an expanded state
If the part cools unevenly then it will warp or lift. This normally happens in the corners of the part
as the corners are exposed to air circulating around the printer. The larger the parts surface area on
the platform, normally the worse the problem.
Some Tips to reduce warping:
• Make sure the
platform
up to near the nozzle and in maintenance, move the head to each corner to ensure the di
tance between nozzle and
• Make sure the
platform
platform
heated after printing)
•
Keep the printer away from any breezes
• Print hollow -
The less mass of plastic the less heat in the centre, the less warping.
•
Print the object with the least surface area on the platform,
more successful printing and saves material in the long run.
• P
rint closer to the Perfboard
• Keep the
Perfboard
4.
Troubleshooting
3D Printer User Manual
v 2013.6.10
The platform rests on a tripod (three
ng screws) and in order to level it
, you
each of the three screws
until the distance between the nozzle a
nd
at each corner.
As the platform gets more level, increase
height to the nozzle, so it is
You will most likely need to repeat the process 5
-9
going in a clockwise manner. Each
educing the amount of turn on the screws.
Loosen a screw and the related corner of platform will rise. Tighten, or loosen, the screws until
you have the same gap between the nozzle and the platform at all four corners of platform.
Tips & Tricks
to avoid warping / lifting
When printing with ABS Plastic
it is important to understand the material. ABS
is extruded from
it comes out in an expanded state
, like most materials as it cools it will shrink.
If the part cools unevenly then it will warp or lift. This normally happens in the corners of the part
as the corners are exposed to air circulating around the printer. The larger the parts surface area on
the platform, normally the worse the problem.
Some Tips to reduce warping:
platform
is level! -
Remove the Perfboard and clips, bring the
up to near the nozzle and in maintenance, move the head to each corner to ensure the di
tance between nozzle and
platform is the same at each corner.
Check and recheck!!!
platform
is nice and toasty!
(do a previous print or two and keep the
heated after printing)
– Keep the extruder
door closed during printing
Keep the printer away from any breezes
, air con, this cools
the model to
The less mass of plastic the less heat in the centre, the less warping.
Print the object with the least surface area on the platform,
creates more support
more successful printing and saves material in the long run.
rint closer to the Perfboard
– Move the nozzle closer to the platform.
Perfboard
smooth -
Clean the perfboard, by scrapping off the surface and e
Troubleshooting
Loosen a screw and the related corner of platform will rise. Tighten, or loosen, the screws until
you have the same gap between the nozzle and the platform at all four corners of platform.
to avoid warping / lifting
is extruded from
, like most materials as it cools it will shrink.
If the part cools unevenly then it will warp or lift. This normally happens in the corners of the part
as the corners are exposed to air circulating around the printer. The larger the parts surface area on
Remove the Perfboard and clips, bring the
platform
up to near the nozzle and in maintenance, move the head to each corner to ensure the di
s-
Check and recheck!!!
(do a previous print or two and keep the
door closed during printing
.
the model to
fast.
The less mass of plastic the less heat in the centre, the less warping.
creates more support
but
Clean the perfboard, by scrapping off the surface and e
n-
… 48 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für 3Dprintingsystems UP Plus wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info