Bedienungsanleitung 3Dprintingsystems UP Plus (Seite 52 von 56) (Englisch)

534678

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

UP Plus

3D Printer User Manual

8.4 How to clean the extruder column

•

First “Withdraw” the filament from the extruder. Once the printer beeps remove the fil

ment from the extruder head.

• Remove the nozzle.

•

Click “Withdraw” again, when the printer beeps.

•

Using the gloves and a 1

silver column of the extruder column removing any plastic residue.

•

Clean the plastic off the drill bit each time.

•

You might need to click “Withdraw” a few times to remove as much plastic residue as

possible.

8.5

How to clean the extruder drive gear

head)

•

First “Withdraw” the filament from the extruder. Once the printer beeps remove the fil

ment from the extruder head.

•

Switch off at the back of the printer and wait for the extruder to cool down.

•

Remove all the connector plugs at the top of the extruder.

Figure a.)

• Remove the

extruder head from the printer

two Alan screws from above the fan that hold the white plastic onto the stepper motor, as

indic

ated with red arrows in (figure b)

•

Pull the plastic part away from the stepper mot

• Place

the Alan key under the drive gear cover (figure

brush clean the plastic dust residue that is inside the drive gear.

•

Replace the drive gear cover and replace the plastic cover.

Note: There ar

e a few different variations of extruder heads, but removal is similar.

Troubleshooting

3D Printer User Manual

v 2013.6.10

8.4 How to clean the extruder column

First “Withdraw” the filament from the extruder. Once the printer beeps remove the fil

ment from the extruder head.

Click “Withdraw” again, when the printer beeps.

Using the gloves and a 1

–

1.5mm drill bit and using your hand twist and poke up into the

silver column of the extruder column removing any plastic residue.

Clean the plastic off the drill bit each time.

You might need to click “Withdraw” a few times to remove as much plastic residue as

How to clean the extruder drive gear

(v2 extruder

First “Withdraw” the filament from the extruder. Once the printer beeps remove the fil

ment from the extruder head.

Switch off at the back of the printer and wait for the extruder to cool down.

Remove all the connector plugs at the top of the extruder.

(figure a)

Figure b.)

extruder head from the printer

using the large supplied Alan key

two Alan screws from above the fan that hold the white plastic onto the stepper motor, as

ated with red arrows in (figure b)

Pull the plastic part away from the stepper mot

or and lay to one side

the Alan key under the drive gear cover (figure

c) and lever

the cover off. Using a

brush clean the plastic dust residue that is inside the drive gear.

Replace the drive gear cover and replace the plastic cover.

e a few different variations of extruder heads, but removal is similar.

Troubleshooting

First “Withdraw” the filament from the extruder. Once the printer beeps remove the fil

1.5mm drill bit and using your hand twist and poke up into the

You might need to click “Withdraw” a few times to remove as much plastic residue as

(v2 extruder

First “Withdraw” the filament from the extruder. Once the printer beeps remove the fil

Switch off at the back of the printer and wait for the extruder to cool down.

Figure b.)

using the large supplied Alan key

. Remove the

two Alan screws from above the fan that hold the white plastic onto the stepper motor, as

the cover off. Using a

e a few different variations of extruder heads, but removal is similar.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

3Dprintingsystems UP Plus Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info