Bedienungsanleitung 3m digital projector x90 (Seite 20 von 70) (Englisch)

215489

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

Adjusting the position

Press the POSITION button on the remote control.

The “POSITION” indication will appear on the screen.

8VHWKHFXUVRUEXWWRQVŸźŻŹWRDGMXVWWKHSLFWXUH

position.

When you want to reset the operation, press the RESET button on the remote

control during the operation.

To complete this operation, press the POSITION button again. Even if you do

not do anything, the dialog will automatically disappear after a few seconds.

Ɣ

When this function is performed on a video signal, s-video signal or component video

signal, some image such as an extra-line may appear at outside of the picture.

Ɣ

When this function is performed on a video signal, s-video signal, or component video signal

of 525i (480i) or 625i (576i), the range of this adjustment depends on the OVER SCAN in

IMAGE menu

(



29)

setting. It is not possible to adjust when the OVER SCAN is set to 10.

ESC MENU RESET

POSITION AUTO

MAGNIFY

MY BUTTON

VOLUME

PUSH

ENTER

PAGE UP

PAGE DOWN

Operating

Correcting the keystone distortions

Press the KEYSTONE button on the

remote control. A dialog will appear on the

screen to aid you in correcting the distortion.

Use the cursor buttons

to select AUTO or

MANUAL operation, and press the button

to perform the following.

1) AUTO executes automatic vertical keystone correction.

2) Manual displays a dialog for keystone correction.

8VHWKHFXUVRUEXWWRQVŻŹWRVHOHFWWKHGLUHFWLRQWRFRUUHFW

(

or ) then use the buttonsŸźIRUDGMXVWPHQW

To close the dialog and complete this operation, press the

KEYSTONE button again. Even if you don’t do anything,

the dialog will automatically disappear after a few seconds.

Ɣ7KHDGMXVWDEOHUDQJHRIWKLVIXQFWLRQZLOOYDU\DPRQJLQSXWV)RUVRPHLQSXW

this function may not work well.

Ɣ:KHQ9,19(57RU+9,19(57LVVHOHFWHGWRWKH0,5525LWHPLQWKH

SETUP menu, if the projector screen is inclined or angled downward, this

function may not work correctly.

Ɣ:KHQWKH]RRPDGMXVWPHQWLVVHWWRWKH7(/(WHOHSKRWRIRFXVWKLVIXQFWLRQ

may be excessive. This function should be used when the zoom adjustment is

set to the full WIDE (wide-angle focus) whenever possible.

Ɣ

When the projector is placed on the level (about ±3°), this function may not work.

ƔWhen the projector is inclined to near ±30 degree or over, this function may not

work well.

Ɣ

When the vertical lens shift is not set fully upward (not set fully downward for the

optional lens type FL-601 only

(



45)

), this function may not work well.

Ɣ

When the horizontal lens shift is not set to the center, this function may not work well.

ƔThis function will be unavailable when Transition Detector is on

(



51).

MAGNIFY

MY BUTTON

VOLUME

ON 1

MUTE

OFF 2

FREEZE KEYSTONE SEARCH

-';5610'



#761':'%76'



/#07#.

 



-';5610'



3M™ Digital Projector X90

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

3m digital projector x90 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info