5551
10
Zoom out
Zoom in
Vorherige Seite
1/36
Nächste Seite
3M
Multimedia Projector MP7760
10
© 3M IPC 2000
3-3. Mouse Connection
The MP7760 has mouse emulation capability. Connect your computer mouse to the MP7760 and control
computer mouse functions using the remote control.
1. Power down the computer and projector.
2. Remove the mouse cable connection from your computer mouse port.
3. Connect the 9-pin D-Sub plug on the mouse cable to the RS-232 port on the projector. (Not necessary for
USB mouse emulation!)
4. RS-232 Serial Mouse: Connect 9-pin D-Sub plug on mouse cable to the serial port on the computer.
PS/2 Mouse: Connect 9-pin D-Sub plug on mouse cable to PS/2 adapter and connect the 6-pin Mini-DIN
adapter plug to the PS/2 port on the computer.
MAC ADB: Connect 9-pin D-sub plug on mouse cable to the Mac ADB adapter and connect the 4-pin
Mini-DIN plug on ADB adapter to the ADB port on the computer.
(The Mac ADB adapter is an accessory item that must be ordered separately.)
USB Mouse: Connect 4-pin USB mouse cable to the computer USB port or to a free USB hub port. On
first startup, the computer will ask for device driver installation and configuration.
(The USB mouse cable is an accessory item that must be ordered separately.)
üü
üü
ü
Note: For serial mouse connections to a laptop computer, refer to the manufacturers
operating instructions. The internal pointing device or serial port configurations may
need to be changed.
5. First, power on the projector, then power on the computer.
üü
üü
ü
Note: Mouse emulation only works when all cable connections are established and the proper
start up sequence is followed. See section 4-1.
üü
üü
ü
Note: The recommended mouse drivers for mouse emulation is the Standard Microsoft Mouse,
Serial or PS/2.
3-4. Cable Connections
1. Turn off all power to the projector and input sources during cable hook-up.
2. Connect cables, being careful not to bend any pins in the cable plug or input terminal (Figure 3-1).
3. Start up projector, then start up input sources (Section 4-1).
Caution
To prevent damage to equipment, all power to MP7760 and input sources must
be turned OFF during cable hook-up.
Section 3: Set-Up/Connections
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für 3m MP7760 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von 3m MP7760

3m MP7760 Bedienungsanleitung - Deutsch - 35 seiten

3m MP7760 Bedienungsanleitung - Holländisch - 36 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info