Bedienungsanleitung 3m MP8020 (Seite 18 von 28) (Englisch)

5553

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

3M Multimedia Projector MP8020

 1996

When the projector is displaying a video or computer image, press the H/V button to switch to the

MENU mode and the LED will begin flashing. Move the trackball left/right to adjust the image

horizontally or up/down to adjust the image vertically. When changes are complete, press the H/V

button to return to the NORMAL mode.

Note

The LED will stop flashing and return the remote control transmitter to the NORMAL mode

after five seconds of inactivity.

Sizes the picture to fit the screen. Press

to make the projected image wider or to reduce the

image size.

Press

or to focus the image.

Turn the audio (speaker) sound ON (mute bar turns green) or OFF (mute bar turns red).

This button displays a digital countdown clock in the upper left corner of the

projection screen. Minutes are displayed on the left and seconds on the right.

You can set the timer for the desired number of minutes to be counted down.

Seconds cannot be set – they are a display only field.

When the projector is in the Normal mode:

a. Press TIMER to display the clock. Figure 52.

b. Press the RESET button to position the cursor in the left most minutes column.

c. Press and hold RESET to put the remote in menu mode (LED will flash).

d. Move the track ball up/down to change the digit.

e. Move the track ball left/right to move to the next column.

f. Press RESET to start the clock.

To reset the clock for a different amount of time, repeat steps b-f. To remove the clock display from

the projection screen, press TIMER.

Press to blank the screen (screen turns blue). Press again to return the normal display.

Press

to decrease or to increase the speaker volume (NORMAL mode) or to move

left/down or

to move right/up to adjust the setting of an on-screen menu line. See MENU

button.

The menu button is used to switch the projector and remote control between the NORMAL (Video

image and LED is Off) and MENU (On-screen Menu and LED is flashing) operating modes.

NORMAL Mode

: (Video image being displayed, LED is Off) The normal operating mode is used to

display normal video images from your video or computer sources. Use the remote control buttons

to adjust the focus and volume levels of the projector and operate the mouse key functions (trackball,

drag, left/right) to control the video presentation.

MENU Mode

: (On-screen Menu being displayed, LED is FLASHING) The MENU operating mode

is used to display on-screen Menus. These menus allow you to adjust the MP8020 projector settings

for best performance.

To make a projector setting change from the on-screen menu:

a. Press and release the MENU button to display the onscreen menu.

b. Press and hold the MENU button for two seconds to change the remote to the MENU

mode. The LED on the remote will flash the entire time the remote is in the menu mode.

c. Move the trackball to make the desired changes on each Menu line.

d. Press the Menu button to return to the NORMAL mode.

e. Wait five seconds for the LED to stop flashing - remote automatically returns to Normal

mode.

H/V

←→

↓

↑

00:00

Minutes : Seconds

Clock Display

Figure 5-2. Clock

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

3m MP8020 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von 3m MP8020

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info