654489
14
Zoom out
Zoom in
Vorherige Seite
1/31
Nächste Seite
++ + FOCUS +++
SETUP INPUT IMAGE OPT.
SETUP INPUT IMAGE OPT.
RGB1
RGB2
VIDEO1
VIDEO2
TEST
PATTERN
11
3M 1996
3M Multimedia Projector MP8030
Mute: Press the MUTE button to turn off the sound to the speakers. Press again to restore the sound.
Note
The volume level is controlled from the remote control transmitter.
Zoom: Press the ZOOM
button to adjust the image size to fill the screen. Press and hold down
+
or
until the image is the desired size. If you cannot make the image fill the screen, move the projector further
back from the screen.
Focus: Press the FOCUS
button to adjust the sharpness of the image.
The following on-screen display will appear:
Press and hold down
+
or
until the image becomes sharp and clear.
Menu: Press the MENU
button to display the names of the system
menus across the top of the projection screen. These menus are used to adjust
the characteristics of the projected image.
MENU
Press the left/right arrow ( MENU ) to select (highlight) and display each menu.
Press the up/down (
MENU ) arrow or left/right ( MENU ) arrow again to select
(highlight) the desired menu option. See Section 4-5 for more about using menus.
Volume Adjustment: Use the VOLUME
button on the remote control to adjust the speaker volume.
Press (
) to increase or ( ) to decrease the volume level. See Section 4-6 to set the volume in the Setup
menu.
4-2. Turning Off the Projector
Press and hold down the STANDBY/ON button for one second to switch the projector to the standby
mode. The one second hold-down period is designed to avoid accidentially turning off the projector if the
standby/on button is bumped. The lamp will shut off and the green indicator on the projector panel will turn to
orange. Wait until the cooling fan motor cycles off before you press the Power Off
switch.
Note
Switching the power off before the fan has cycled off, will decrease the life of the projection lamp.
4-3. Memory Function/Factory Defaults
The MP8030 will retain all picture adjustment settings you make until you either change them again or return
all settings to the factory default.
To return picture adjustments back to the factory settings, press the RESET button on the projector control
panel or remote control transmitter .
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für 3m MP8030 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info