439701

3m ohp1808 overhead projector Seite 13

13
Zoom out
Zoom in
Vorherige Seite
1/22
Nächste Seite
© 3M 2005. All Rights Reserved. 5 3M™ Overhead Projector 1800 Series
WARNING English
To reduce the risk of various hazards associated with this product:
- Read, understand, and follow all safety information contained in this manual prior to using this overhead projector. Always
ensure that the equipment is used safely. Retain these instructions for future reference.
- Close supervision is necessary when this projector is used by or near children. Do not leave projector unattended while in use.
- The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire, electric shock or injury to
persons.
To reduce the risk associated with hazardous voltage and/or fire:
- Always switch power off and unplug projector from electrical outlet before cleaning and servicing and when not in use. Never
yank cord to pull plug from outlet. Grasp plug and pull to disconnect.
- Do not operate projector with a damaged cord or if the appliance has been dropped or damaged – until it has been examined by
a qualified service technician.
- Service/repair or maintenance must only be performed by qualified service personnel. Do not disassemble this appliance
yourself; incorrect reassembly can cause electric shock when the projector is used subsequently.
- If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. Cords rated
for less amperage than the projector may overheat.
- Connect this projector to a grounded outlet.
- Do not immerse this projector in water or other liquids.
- Replace failed fuse only with the same type and rating as specified on fuse label.
- Never store the power cord or any other articles inside the projector's enclosure.
- Disconnect this projector from its source of supply before replacing the projection lamp or performing any other service.
CAUTION
To reduce the risk of various hazards associated with this product:
- Position the projector's cord so that it will not be tripped over, pulled, or contact hot surfaces. The socket outlet must be installed
near the equipment, and easily accessible.
- Do not expose this projector to direct sunlight; also do not use outdoors or in other wet environments.
- Always operate projector on a flat, sturdy surface.
To reduce the risk associated with hot surfaces produced by the projection lamp:
- Never touch the projection lamp or surrounding surfaces while the lamp is still hot.
- Switch unit off "0", remove the power cord from the electrical outlet, and allow the unit to cool completely before replacing the
lamp.
- Let projector cool completely before putting away. Use cord storage or loop cord loosely around appliance when storing.
To reduce the risk associated with pinching and/or piercing:
- Use care when opening or closing glass platten (top cover) to ensure it does not fall uncontrollably.
- Keep hands away from the interlock actuator located on the top cover when closing.
To reduce the risk associated with sharp glass fragments:
- Use care when removing lamp glass that has failed and shattered into sharp pieces.
- Use care when removing glass from a broken projection lens.
To reduce the risk associated with muscular strain:
- Weight of projector is approximately 28 Lbs (12.8 Kg); utilize the built-in handles and proper lifting technique when lifting this
projector. Never lift projector by its foldable arm.
To reduce the risk associated with high temperatures and/or related fire:
- Replace failed lamp only with type specified on lamp label.
Important Notes
The appliance switch is provided with the symbols "O" indicating OFF, and "I" indicating ON.
Keep ventilation openings free of any obstructions.
Let overhead projector cool completely before putting away. Store the power cord so that it will not be damaged.
Care must be taken to ensure the smooth airflow of the cooling system. Immediately switch off the machine if the fan is not
functioning properly.
Make sure that the operating voltage of the overhead projector corresponds to your local voltage.
Do not use detergents, chemicals, or any spray liquids for cleaning this unit, other than those referred to in the “Operators Guide”.
SAVE THESE INSTRUCTIONS
… 13 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für 3m ohp1808 overhead projector wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info