Bedienungsanleitung 3m S10 (Seite 32 von 45) (Englisch)

5603

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

Lamp

The projector uses a high-pressure mercury glass lamp. The lamp can break with a

loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.

Note that each lamp has a different lifetime, and some may burst or burn out soon after

you start using them. In addition, when the bulb bursts, it is possible for shards of

glass to fly into the lamp housing, and for gas containing mercury to escape from the

projector’s vent holes.

• If the lamp should break (it will make a loud bang when it does), unplug the power

cord from the outlet, and make sure to request a replacement lamp from your local

dealer. Note that shards of glass could damage the projector’s internals, or cause

injury during handling, so please do not try to clean the projector or replace the lamp

yourself.

• If the lamp should break (it will make a loud bang when it does), ventilate the room

well, and make sure not to breathe the gas that comes out of the projector vents, or

get it in your eyes or mouth.

• Do not open the lamp cover while the projector is suspended from above. This is

dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover

is opened. In addition, working in high places is dangerous, so ask your local dealer

to have the lamp replaced even if the bulb is not broken

• If the indicators or a message prompts you to replace the lamp (see the section

“Related Messages” and “Regarding the indicator Lamps”), replace the lamp as soon

as possible. Using the lamp for long periods of time, or past the replacement date,

could cause it to burst. Do not use old (used) lamps; this is a cause of breakage.

• If the lamp breaks soon after the first time it is used, it is possible that there are

electrical problems elsewhere besides the lamp. If this happens, contact your local

dealer or a service representative.

• Use the lamp of the specified type only. See the section “ACCESSORIES”.

• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

• Before replacing the lamp, make sure the power switch is off and the power cable is

not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently. Handling

the lamp while hot can cause burns, as well as damaging the lamp.

• Do not use the projector with the lamp cover removed. At the lamp replacing, make

sure that the screws are screwed in firmly. Loose screws could result in damage or

injury.

• Obey local ordinances when disposing of used lamps. In most cases, it is possible to

dispose of used bulbs in the same manner as used glass bottles, but in some cases,

bulbs are sorted separately.

WARNING

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

01S10En 03.9.24 5:07 PM ページ 32

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

3m S10 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von 3m S10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info