Bedienungsanleitung 3m S20 (Seite 31 von 46) (Englisch)

5607

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

OPTION Menu

With the OPTION menu, the items shown in the table below can be performed.

Perform each operation in accordance with the instructions in the table below.

: SELECT

MAIN

PICTURE-1

PICTURE-2

INPUT

AUTO

SCREEN

OPTION

VOLUME

SCREEN TYPE

LAMP TIME

FILTER TIME

RESET

4:3

1234h

21h

Item Description

VOLUME

Adjust Volume: High ⇔ Low

SCREEN TYPE

Select the Screen Type:

4:3 ⇔ 16:9 ⇔ 16:9 ⇔ 16-9

• Please select the screen type used and the picture position in case of 16:9.

This selection is used as basic information for a suitable display. This function

should be performed before other picture adjustment.

LAMP TIME

To begin the operation of this item, please press the button of the

projector or the RESET button of the remote control for 3 seconds.

Reset the Lamp Timer:

Selecting the RESET performs this function.

RESET CANCEL

• The numerical value of four digits shown on this menu is the projector use

time since the last RESET operation of this item. The value is reset to 0 at the

same time the RESET is selected.

• The value of this function is used to display the message of “CHANGE THE

LAMP”. So this function must be performed only immediately after replacing

the lamp.

Do not perform this function unless you have replaced the lamp. Perform this

function every time the lamp is replaced. Incorrect performing of this function

causes incorrect operation of the message function.

• Please see to the section “Lamp” about replacing the lamp.

FILTER TIME

To begin the operation of this item, please press the button of the

projector or the RESET button of the remote control for 3 seconds.

Reset the Filter Timer:

Selecting the RESET performs this function.

RESET CANCEL

• The numerical value of four digits shown on this menu is the projector use

time since the last RESET operation of this item. The value is reset to 0 at the

same time the RESET is selected.

• The value of this function is used to display the message of “CLEAN THE AIR

FILTER”. So this function must be performed only immediately after cleaning

or replacing the air filter.

Do not perform this function unless you have cleaned or replaced the air filter.

Perform this function every time the air filter is cleaned or replaced. Incorrect

performing of this function causes incorrect operation of the message

function.

• Please see to the section “Air Filter” about cleaning and replacing the air

filter.

RESET

Reset the OPTION Menu Items:

Selecting the EXECUTE performs this function.

EXECUTE CANCEL

• The SCREEN TYPE item is returned to the initial setting. Note that the items

VOLUME, LAMP TIME and FILTER TIME are not reset.

⇒

Multifunctional Settings (continued)

01S10En 03.9.24 5:07 PM ページ 31

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

3m S20 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von 3m S20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info