Bedienungsanleitung A.Caminetti Flat (Seite 27 von 30) (Englisch)

813873

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Insulating layers (protection of standard walls)

- The forewall (22) and the wall of the building (20) must be protected by an insulating layer (4, 16)

with a minimum thickness of 9 cm.

- The surrounding (11) does not need to be protected by the insulating layer if the construction is

protected so that the surface of the surroundings heats to a maximum of 85°C. For natural stone

or ceramic surfaces where no items will be placed, the surface temperature may increase to

amaximum of 120 °C (applies to large slopes or vertical areas of the surroundings - heated tiled

walls, etc.).

Protection of the ﬂoor

- Floors from ﬂammable materials must be protected by the concrete plate (7) with a minimum

thickness of 6 cm, which must have an insulating layer (9).

- Load-bearing ﬂoors and ﬂoors from reinforced concrete must be protected by an insulating

layer (9).

Surroundings

- The walls of the surroundings distribute the heat into the room and must be from non-ﬂammable

class A1 materials.

- Natural stone or ceramic vertical areas in the room can reach a maximum temperature of 120°C.

- Horizontal areas where items may be placed can reach a maximum temperature of 85 °C.

- The surroundings must not be connected to the ﬁreplace insert and must be self-bearing.

- Between the ﬁreplace insert and the surroundings, as well as the bearing frame and the

surroundings, sealing tape or insulating paper must be inserted to covers the difference in the

heat expansion of the material.

Ventilation grids

- For the output ventilation grid, a minimum distance of 50 cm from the ceiling must be maintained

and 30 cm from walls from ﬂammable materials, load-bearing concrete walls and

built-infurniture.

- Output ventilation grids must be positioned proportionally from the upper part of the

surroundings so that there is no accumulation of heat in the surroundings. During the positioning

of the grids, be aware of any potential problems with cleaning the grids.

- The value of the free cross-section of the grids depends on the material in the surroundings and

the type of the ﬁreplace insert (see technological sheets).

- Ventilation grids must be positioned so they cannot be blocked.

Insulation of the ceiling

- If the surroundings include the ceiling, this must be protected by the respective insulation

according to local installation standards.

Floor in front of the ﬁreplace insert

- The ﬂoor in front of the ﬁreplace insert must be from non-ﬂammable materials or protected by a

sufﬁciently thick non-ﬂammable board (e.g. foundation glass).

- Non-ﬂammable area:

- In the forward direction, it depends on the height of the bottom of the combustion chamber

from the ﬂoor, it is necessary to add to this height 30 cm; the minimum value is 50 cm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

A.Caminetti Flat Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info