Bedienungsanleitung A.O. Smith ADM 115 (Seite 13 von 64) (Englisch)

503294

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Instruction manual ADM 13

gis

2.4 Protection for the

appliance

The burner control monitors the water temperature by means of thermostats

and ensures safe combustion. This takes place using:

• the Gas control;

• the Thermocouple

;

• the Water temperature protection

;

• the Flue gas backflow safeguard.

2.4.1 Gas control

The gas control has 2 valves for safety purposes:

1. The main valve, which controls the gas supply to the burner tray and which

is switched via the I/0/II switch circuit and the control, high-limit and flue gas

thermostats. This circuit is powered by the supply voltage.

2. The safety valve, which controls the gas supply to the pilot burner and which

is switched via the thermocouple circuit and the safety thermostat. This

circuit is powered by the millivoltage from the thermocouple that is located

in the pilot flame. Whenever the safety valve closes, the main valve also

closes.

2.4.2 Thermocouple

1. To prevent gas flowing when there is no combustion, a thermocouple is

fitted. As a result of the presence of the (permanent) pilot flame, the

thermocouple maintains a millivoltage which keeps the gas control's safety

valve open.

2. If the pilot flame goes out, this voltage disappears and the gas control's

safety valve closes, interrupting the gas supply to the burner tray.

2.4.3 Water temperature protection

The burner control monitors three temperatures related to safety using the frost

and high-limit thermostats. The table explains the operation of the thermostats

with sensors.

Temperature protection

2.4.4 Flue gas backflow safeguard

To prevent the flue gases from flowing back into the appliance, is flue gas

sensor (34) and flue gas thermostat (37) have been fitted to the draught diverter.

Under normal conditions, this sensor will register the ambient temperature.

However, if the chimney does not draw sufficiently (for example due to a

blockage in the chimney) then the flue gases will 'reflux' and flow back past the

flue gas sensor. The sensor will then detect an unusually high temperature and

the flue gas thermostat will open. The gas control's main circuit closes, which

interrupts the heating cycle. The flue gas thermostat is blocked and the

appliance must be restarted manually.

Protection Description

High-limit thermostat The heat demand is ended by closing the gas control. This terminates the

heating cycle. The heating cycle restarts once the high-limit thermostat closes.

This happens because the pilot light stays lit when the gas control is closed.

The high-limit thermostat prevents overheating and/or excess lime buildup.

Safety thermostat If the safety thermostat sensor (38) registers a temperature that is higher than

93 °C, the power to the thermocouple is switched off. This terminates the

heating cycle. It is then only possible to restart the appliance using the spark

igniter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

A.O. Smith ADM 115 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von A.O. Smith ADM 115

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info