Bedienungsanleitung A.O. Smith ADMR135 (Seite 55 von 96) (Englisch)

503238

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Instruction manual ADMR 55

gis

11 Main menu

11.1 Notational convention for menu-related

instructions

The

( ) of the electronic controller is divided

into submenus. For example,

SETTINGS

is one of the

functions reached from the main menu. The

SETTINGS

menu is divided into submenus in turn.

For example,

LANGUAGE

is a submenu of

SETTINGS

. So, for example, to select the

LANGUAGE

menu, this manual uses the following

notational convention:

• :

SETTINGS

LANGUAGE

Confirm with .

This means:

1. : Activate the main menu with .

SETTINGS

: Use the and/or buttons to go to

SETTINGS

and confirm with .

LANGUAGE

: Use the and/or buttons to go to

LANGUAGE

4. Confirm with . After entering , you

will have activated the

LANGUAGE

submenu.

11.2 Switching on the "ON mode"

You can switch the appliance to the

mode from any

operational mode, as follows:

1. :

START OPERATION

Confirm with .

Note

First consult the chapter about switching

on (9 "Starting and running") too.

11.3 Setting the water temperature

11.3.1 Setting the water temperature via

the SET POINT MENU

The water temperature can be set to any value

between 40 °C and 80 °C.

Set the water temperature via:

1. :

CHANGE SETPOINT

Confirm with .

2. Use:

• to increase the value;

• to decrease the value.

• Confirm with .After confirming, the

appliance enters "ONmode".

Note

If the preset temperature is higher than the current

water temperature, then the appliance might not

immediately start the heating cycle. To prevent

excessively frequent switching on and off, there is a

heating margin. The standard setting for this margin is

4 °C. The appliance starts heating when the water

temperature is 4 °C colder than the SETPOINT.

We refer to this margin as the hysteresis. The service

and maintenance engineer can adjust (12.2 "Setting

the hysteresis") this setting.

11.3.2 Setting water temperature during

ON mode

The water temperature can also be directly adjusted

when the appliance is in the "ON mode". Simply use:

• to increase the value;

• to decrease the value.

• Confirm with .

11.4 Week program

Using the week program, you can set the water

temperature for the days and times you want.

If the appliance is running under a week program, this

is indicated on the display by the

PROG

text on the first

line (see the figure). The second line shows the time

of day, the day of the week and the temperature. The

third line shows the next switching time of the week

program and the programmed temperature. The fourth

line shows the

PROGRAM ACTIVATED

text.

START OPERATION

^»CHANGE SETPOINT

È Tset=65ÉC

SETPOINT

» 65ÉC

13:45 Thursday 65ÉC

Tset»65ÉC

PROG

07:55 Monday 64ÉC

MO 08:00 Tset 75ÉC

PROGRAM ACTIVATED

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

A.O. Smith ADMR135 Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von A.O. Smith ADMR135

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info