Bedienungsanleitung A.O. Smith BFC60 (Seite 60 von 100) (Englisch)

503218

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Main menu

60 Instruction manual BFC

gis

2. Use:

• to increase the value;

• to decrease the value.

• Confirm with .After confirming, the

appliance enters "ON mode".

Note

If the preset temperature is higher than the current

water temperature, then the appliance might not

immediately start the heating cycle. To prevent

excessively frequent switching on and off, there is a

heating margin. The standard setting for this margin is

5°C. The appliance starts heating up if the water

temperature is 5°C below the SETPOINT.

We refer to this margin as the hysteresis. The service

and maintenance engineer can set (12.2 "

Setting the

hysteresis") the hysteresis value.

11.4.2 Setting water temperature during

ON mode

The water temperature can also be directly adjusted

when the water heater is in "ONmode". Simply use:

• to increase the value;

• to decrease the value.

• Confirm with .

11.5 Week program

Using the week program, you can set the water

temperature for the days and times you want.

If the appliance is running under a week program, then

this is indicated on the display by the text

PROG

on the

first line (see the figure). The second line shows the

time of day, the day of the week and the temperature.

The third line shows the next switching time of the

week program and the programmed temperature. The

fourth line shows the text

PROGRAM ACTIVATED

The appliance's default week program switches the

appliance on every day at 00:00 and off at 23:59. The

default water temperature setting is 65

If you want, you can change every setting in the

appliance's standard week program.

If the water temperature becomes too low while the

week program is running, the appliance will run

through the heating cycle (9.3 "

The appliance's

heating cycle") and return to the week program.

The following topics are covered here:

• Starting and stopping the week program

• Changing the appliance's standard week program

• Adding times to a week program

• Deleting times from a week program

11.6 Starting and stopping the week

program

The week program can be started up from any other

operating mode, as follows:

1. :

WEEK PROGRAM

START OPERATION

Confirm with .

A week program can be shut down simply by

activating a different operating mode, for example the

"ON mode".

11.7 Changing the appliance's standard

week program

Note

First fill-in the desired week program on the

supplied week program card.

A week program is made up of a number of

programmable periods in which you can have the

appliance switch on and off. A period consists of:

• switch-on time: day of the week, hours and

minutes:

• switch-off time: hours and minutes;

• the water temperature setting;

• on/off setting for a program-controlled pump.

Note

The switch-off time must always be followed by a

switch-off time on the same day of the week. A

maximum of three periods may be programmed per

day. You can program a maximum of 21 periods.

Call up the menu for the week program as follows:

•:

WEEK PROGRAM

PROGRAM OVERVIEW

Confirm with .

SETPOINT

» 65ÉC

13:45 Thursday 65ÉC

Tset»65ÉC

PROG

07:55 Monday 64?C

MO 08:00 Tset 75?C

PROGRAM ACTIVATED

WEEK PROGRAM

START OPERATION

^»PROGRAM OVERVIEW

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

A.O. Smith BFC60 Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von A.O. Smith BFC60

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info