Bedienungsanleitung A.O. Smith BTI 100 (Seite 19 von 28) (Englisch)

671757

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

2.5 Temperature regulation

The appliance is under water supply

pressure (maximum 8 bar). The amount

of cold water that is added is equal to

the amount of hot water used. The gas

control block automatically regulates the

gas supply. The main burner will ignite as

soon as a reduction in water temperature

is sended by the thermostat. The main

burner will shut down as soon as the

preset temperature is achieved.

At high water temperatures there is more

scale buildup in the appliance. It is for

this reason that it is recommended to

place the temperature control knob in

position of 60 °C as the accumulation of

scale will be reduced.

2.6 Converting to another

type of gas

For conversion of the appliance from

natural gas to another type of gas, or

visa versa, it is necessary to exchange

the pilot injector and the main injector.

The conversion may only be executed by

a qualed competent person.

Procedure:

1. Shut the heater down. Close the main

inlet gas valve and switch off the

electricity supply at the main switch;

2. Remove the burner assembly;

3. Replace the injectors with the correct

injectors from the conversion set.

(see table below).

Remark:

- When conversion of the appliance

from natural gas to another type of

gas, x the screw on the gas block

of the burner pressure control as

far as the stop.

- When conversion of the appliance

from another type of gas to natural

gas, then the right burner pressure

should be adjust.

2.7 Maintenance

To ensure safe and efcient operation of

the water heater it is recommended that

it is cleaned and serviced at least once a

year by a qualied competent person.

2.7.1 Magenesium anode

The life cycle of the anode is determined

by the quality and the quantity of the

water owing through the water heater.

It is therefore recommended that the

anode be inspected and replaced if

necessary at least once a year.

1. Close the stop cock in the cold water

supply pipe;

2. Open the nearest hot water tap in

order to allow the pressure to drop

from the water heater and the pipes;

3. Slacken the anode with a tting

wrench;

4. Check the anode and replace it if it

has been reduced in diameter by 60%

or more at any point on its lenght;

5. Check for water leaks.

If is necessary to replace the anode it

should be replaced by one of the same

type. The type of anode required can be

detemined on the basis of the type of the

appliance and the serial number.

2.7.2 Cleaning

1. Close the gas supply and demount

the burner after it has cooled down

2. Disconnect the burner assembly from

the gas control

3. Remove the complete burrner

assembly

4. Clean the burner with a soft brush

5. Check the pilot burner and clean it if

so required

6. Check the combustion chamber, ue

tube and ue bafe and clean these if

required

After cleaning of the pilot- and main

burner the operation of these should

be checked. If necessary the burner

pressure should be reset.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

A.O. Smith BTI 100 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info