Bedienungsanleitung A.O. Smith BTI 85 (Seite 16 von 28) (Englisch)

671756

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

2.1.3 Gas connection

The gas supply to this appliance must

be installed in accordance with BS 6891

(1988) and British Gas Publications UP1

and UP2.

Fit the 1/2” gas supply cock supplied

with this unit immediately before the

gas control. No heat or soldered joints

should be applied in the vicinity of the

gas control, as they could cause damage

to the control. All connections and joints

should be tested for gas soundness with

a suitable leak detector (do not use a

naked ame).

N.B. When operating this unit on LPG a

suitable gas supply cock should be used.

2.1.4 Flue system

The water heater should be tted with

a ue system connected to the draught

diverter. The ue pipe should rise for

at least 50 cm. vertically before the

inclusion of any bends. If a horizontal

run of ue is required this should be

kept to the minimum lenght possible and

incorporate a rise of 6 cm. per metre

of run. A split clip or ange should be

provided in the ue close to the draught

diverter for ease of servicing.

All ue materials should be corrosion

resident i.e. stainless steel or galvanised

and must include a tested and apprved

terminal to BS 5440 part 1.

If the ue passes through any

combustible marerial measures must be

taken to protect against the possibility

of re.

All ues must terminate in free air space

approx. 1,5 metres from any vertical

surface of structure i.e. chimney stacks,

roof parapets, etc. If an existing chimney

or ue is to be used this should be swept

clean and be free of debris before an

approved liner is installed and connected

to the water heater.

2.1.5 Draught diverter

The appliance has been tted with a

ue down draught safety device. The

operation of the safeguard is based

on the principle of the Thermal Reux

Safeguard (TRS).

This TRS can be recognized by the copper

coloured spiral that is tted to the lower

edge of the draught diverter. The spiral is

connected to a thermostat by means of a

capillary tube. The wiring of the thermostat

must be connected to the thermocouple

circuit.

Important

The TRS should never be put out of

operation. The reentry of ue gasses

may cause poisoning.

2.1.6 Electrical connection

All electrical connections must be carried

out in accordance with IEE regulations

by an accredited electrical installation

company. The appliance must be

connected to the mains by means of

a permanent electrical connection. A

main switch must be tted in the phase

between the permanent connection and

the water heater. The feeder cable must

have cores of at least 3 * 1.0 mm

The

connecting clamps for the electricity supply

are indicated by the symbol for earth Á,

N for neutral and L for live. Always check

with a voltage tester if the live and the

neutral have been connected correctly in

the electricity supply. The electricity supply

must comply with the requirements below:

Electrical Frequency Electrically

supply fused to a

minimum of

220/240 V AC 50 Hz 5A

The maximum power consumption is

25 W

See electrical diagram for more

information, appendix 1.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

A.O. Smith BTI 85 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info