503271
57
Zoom out
Zoom in
Vorherige Seite
1/126
Nächste Seite
Caution
The installation diagram shows a pump station with an integrated non-return valve. This
type of pump unit may only be used with closed systems. In systems with drain-back,
installation of a pump unit with non-return valve is prohibited. There are special pump
units for these systems. Please contact the pump unit supplier for this.
Note
Use this installation diagram when you:
install the water connections (see section 7.4)
install the condensate drain
install the gas connection (see section 7.5)
fill the water heater
drain the water heater
n
7.4 Water connections
7.4.1 Unvented water connections
Warning
The installation should be carried out by a competent person, in compliance with general
and locally applicable regulations.
7.4.1.1 Cold water side
See (A) in the installation diagram.
Fit an approved stop valve (4) on the cold water side as required by the applicable
regulations.
The maximum working pressure of the water heater is 8 bar. Because the pressure
in the water pipe at times can exceed 8 bar, you must fit an approved pressure-
reducing valve (1).
Fit a non-return valve (5) and an expansion vessel (16).
Fit an expansion valve (15) and connect the overflow side to an open waste water
pipe.
7.4.1.2 Hot water side
See (B) in the installation diagram.
Note
Insulating long hot water pipes prevents unnecessary energy loss.
Optional: fit a temperature gauge (12) so you can check the temperature of the tap
water.
Fit the T&P valve (3).
Fit a stop valve (11) in the hot water outlet pipe for servicing.
7.4.1.3 Circulation pipe
See (C) in the installation diagram.
If an immediate flow of hot water is required at draw-off points, a circulation pump can be
installed. This improves comfort, and reduces water wastage.
Fit a circulation pump (6) of the correct capacity for the length and resistance of the
circulation system.
Fit a non-return valve (5) after the circulation pump to guarantee the direction of
circulation.
Fit two stop valves for servicing (4).
Connect the circulation pipe according to the installation diagram.
c
w
1.
2.
3.
4.
n
1.
2.
3.
1.
2.
3.
4.
0311753_SGS_28-120_II_UKUK_V2.0 , 2017-05-03 57
57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für A.O. Smith SGS 30 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von A.O. Smith SGS 30

A.O. Smith SGS 30 Bedienungsanleitung - Deutsch - 128 seiten

A.O. Smith SGS 30 Bedienungsanleitung und Installationsanweisung - Holländisch - 120 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info