503271
74
Zoom out
Zoom in
Vorherige Seite
1/126
Nächste Seite
If there is nothing else you need to check or adjust, you can put the covers back on
the appliance.
7.9.3 Procedure for checking the gas control valve pressure
The procedure for checking the gas control valve pressure is only applicable to appliances
that have a pressure-reducing valve. If the appliance does not have a reducing valve,
continue from adjusting the CO
2
value (see section 7.9.4).
To check the gas control valve pressure, proceed as follows:
Isolate the appliance from the power supply (see section 4.2.2).
Carefully remove the covers from the appliance.
The electrical section is now visible.
The gas control valve has a test nipple that can be used for measuring the gas
control valve pressure. This test nipple has a sealing screw. Loosen the sealing screw
by a few turns. Do not completely loosen it as it can be difficult to retighten.
Open the gas supply.
Connect a pressure gauge to the test nipple.
Switch on the power to the appliance using the isolator on the appliance.
Switch the controller ON by setting the 0/I switch to position I .
The display will now show INTERNAL CHECK for about 10 seconds, and will then go
to the main menu.
7.9.3.1 Procedure for checking the gas control valve pressure
Select SERVICE OPERATION, FULL LOAD from the service menu.
Confirm with [ENTER].
The display shown here will appear.
The appliance is now in PARTIAL LOAD mode and will ignite.
You must wait about 1 minute after the display shows the text RUNNING before
reading the dynamic pressures (the fan needs this time to get up to full speed, so
that a reliable reading can be obtained).
Use the pressure gauge to read the pressure and compare it against the value from
the gas table (see section 12.3).
If necessary, adjust the gas control valve pressure using the reducing valve's
adjuster screw (2) until the value is within the range listed in the table.
16.
1.
2.
3.
4.
5.
6.
7.
8.
1.
2.
3.
4.
5.
74 Installation, Maintenance and Service part
74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für A.O. Smith SGS 30 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von A.O. Smith SGS 30

A.O. Smith SGS 30 Bedienungsanleitung - Deutsch - 128 seiten

A.O. Smith SGS 30 Bedienungsanleitung und Installationsanweisung - Holländisch - 120 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info