503271
97
Zoom out
Zoom in
Vorherige Seite
1/126
Nächste Seite
Indication Cause Measure
Insufficient or no hot
water
The water heater is off. Turn on the water heater (see section 4.1).
There is no supply voltage. Make sure that:
the control switch is set to I.
the isolator is in ON position.
there is power on the isolator.
there is power to the electrical connector
block.
The measured voltage must be
230 V
AC
(-15%, +10%).
The hot water supply is used up. Reduce the hot water consumption. Wait
until the water heater heats up.
The controller is in the OFF mode. Set the controller in the ON mode.
The temperature (T
set
) is set too low. Set the temperature (T
set
) to a higher value.
Glycol leakage Leakage from a fluid connection
(threaded)
Tighten the threaded connection.
Leakage from a component Tighten component joints
Any defective components must be
replaced
1.
2.
Leakage from solar heating system Consult the supplier and/or manufacturer
11.1.2 Displayed errors
Note
For the coding of the connections, refer to the Electrical wiring diagram.
Note
Contact your service and maintenance engineer if the error persists.
Code and description Cause Measure
S01 (blocking error)
Open circuit from
temperature sensor T
2
at
the bottom of the tank.
Sensor is not (correctly) connected Connect the sensor lead to JP3
Damaged cable and/or defective sensor Replace the cable and/or sensor
S02 (blocking error)
Open circuit from sensor 1
of temperature sensor T
1
at the top of tank
(1).
Sensor is not (correctly) connected Connect the sensor lead to JP5
Damaged cable and/or defective sensor Replace the cable and/or sensor
S03 (blocking error)
Open circuit in sensor 2 of
temperature sensor T
1
at
the top of the tank
(1)
.
Sensor is not (correctly) connected Connect the sensor lead to JP5
Damaged cable and/or defective sensor Replace the cable and/or sensor
S04 (blocking error)
Open circuit from
dummy 1.
Dummy is not (correctly) connected Connect the dummy sensor (dummy sensor
1 and 2) leads to JP4.
Defective dummy Replace the dummy sensor
S05 (blocking error)
Open circuit from
dummy 2
Dummy is not (correctly) connected Connect the dummy sensor (dummy sensor
1 and 2) leads to JP4.
Defective dummy Replace the dummy sensor
n
0311753_SGS_28-120_II_UKUK_V2.0 , 2017-05-03 97
97

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für A.O. Smith SGS 30 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von A.O. Smith SGS 30

A.O. Smith SGS 30 Bedienungsanleitung - Deutsch - 128 seiten

A.O. Smith SGS 30 Bedienungsanleitung und Installationsanweisung - Holländisch - 120 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info