503271
102
Zoom out
Zoom in
Vorherige Seite
1/126
Nächste Seite
Code and description Cause Measure
E03 (lock-out error)
Error in temperature
sensor T
1
at the top of the
tank.
The two temperature sensors in the tank
detect a difference of > 10°C over a
period of at least 60 seconds.
Check sensor position and wiring.
Reset the controller if necessary. Replace
the sensor if the error persists.
1.
2.
E04 (lock-out error)
Defect in the dummy
sensor
(2)
.
The two temperature sensors detect a
difference of >10 ºC over a period of at
least 60 seconds.
Check the wiring of the dummy 1 and
dummy 2.
Reset the controller if necessary. Replace
the dummy sensor if the error persists.
1.
2.
11.1.3 Warnings
Note
For the coding of the connections, refer to the Electrical wiring diagram.
Indication Cause Remark
Maximum burning hours:
Service is required
The actual burning hours have exceeded
the pre-set burning hours.
The water heater operates, but displays this
warning.
Periodic maintenance is a part of the
Warranty. When you do not obey this
condition, the warranty will void.
Anode protection is not
working
The cables between the potentiostat
and anodes are loose or have been
connected incorrectly.
The earth connection of the anodes is
loose.
The water heater is not filled with
water.
Connect the wiring correctly and the
warning will disappear.
If the wiring is correct but the warning
remains, check that the earth connection
is good and whether the tank is filled with
water.
Note
The water heater is functioning, but there is
no anode protection for the tank.
1.
2.
n
Solar heating system
pump or Q/T sensor not
correctly connected
Lead(s) loosened or incorrectly
connected
Connect the pump or Q/T sensor properly
and the warning will disappear.
If correctly wired but the warning
remains, replace pump or sensor.
To replace the necessary parts, you must
contact your installation engineer
1.
2.
Q/T sensor not identified Identification failed Disconnect appliance and Solar Heat
Master briefly from the mains.
Check the wiring.
If disconnecting has not helped and the
wiring is okay, and the Q/T sensor still
isn't recognized, then the Q/T sensor or
the Solar Heat Master is defective.
1.
2.
3.
n
102 Installation, Maintenance and Service part
102

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für A.O. Smith SGS 30 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von A.O. Smith SGS 30

A.O. Smith SGS 30 Bedienungsanleitung - Deutsch - 128 seiten

A.O. Smith SGS 30 Bedienungsanleitung und Installationsanweisung - Holländisch - 120 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info