Bedienungsanleitung A.O. Smith Upsilon UB-110 (Seite 57 von 68) (Englisch)

671771

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Installation and Service Manual Upsilon-Series

Block.

B000sc00

Error

E000sc00

Message

M000sc00

14 Errorreport

On the display, errors found are shown in the form of a message or blocking on a blue

screen or an error on a red screen.

- Blocking This is a temporary error that will sort itself out, or it will block the

boiler after several attempts (error)(Except: Bx01sc01 = reset)

- Error Error implies a blocking of the boiler and can only be solved by a

reset and/or intervention of a service engineer.

- Message Implies a message such as low water pressure, but the device will

remain operational.

Point of attention requiring short-term intervention.

The code consists of a Main Code and a Subcode

Main code Blocking = B

Main code Error = E

Main code Message = M

Followed by a character 0 = boiler

1 = burner A

2 = burner B

Subcode always starts with sc

Bx01sc01 Fan does not run on correct speed (Reset necessary). Fan defective.

Bx03sc01* Flow sensor T1 open

Bx03sc02* Flow temperature T1 too high

Bx03sc03* Flow sensor T1a open

Bx03sc04* Flow temperature T1a too high

Bx05sc01* Return sensor T2 open

Bx05sc02* Return temperature T2 too high

Bx08sc01* General purpose contact open

Bx12sc01* Water pressure sensor open

Bx12sc02* Water pressure sensor closed

Bx12sc03* Water pressure lower than 0.7bar. Top up

Bx12sc04* Water pressure too high. Decrease pressure

Bx12sc05* No pressure increase on pump start

Bx13sc01* DT between T1 and T2 too high

Bx15sc01* Communication error between controls

Ex01sc01* Fan does not run on correct speed. Fan defective.

Ex02sc01* No ame after 4 start attempts

Ex02sc02* Insufcient ionisation

Ex04sc01* Flow temperature T1 too high

Ex04sc02* Flow sensor T1 closed

Ex04sc03* Flow temperature T1a too high

Ex04sc04* Flow sensor T1a closed

Ex06sc01* Return temperature T2 too high

Ex06sc02* Return sensor T2 closed

Ex18sc01* Unwanted ame forming

Ex14sc01* DT not fast enough

Ex14sc02* DT between T1 and T2 > 35°C

M024sc01 DHW sensor T3 open (when P122=1)

M024sc02 DHW sensor T3 closed (when P122=1)

M024sc03 Outside sensor T4 open

M024sc04 Outside sensor T4 closed

M024sc05 Common ow sensor T10 open

M024sc06 Common ow sensor T10 closed

M024sc08 Bus communication: Possibly no bus communication cable connected

Mx24sc09 Temperature increase (Gradient) not fast enough after burner start

Mx24sc10 DT between T1 and T2 > 35°C when gas valve opened

* When this code is shown with an M instead of a B or E then a reset with the reset button is possible.

OpenThermerrormes-

sages

Thecodingofthetrans-

mittedErrorMessages

onaOpenThermcon-

trollerisdisplayedas

follows:

(E)EB(E=ErrorCode=

Bandboilernumber)

example:ErrorCode

Ex02SC02onboiler6

willappearas(0)26

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

A.O. Smith Upsilon UB-110 Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von A.O. Smith Upsilon UB-110

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info