Bedienungsanleitung AAS Tassman 4 (Seite 110 von 177) (Englisch)

541310

110

Zoom out

Zoom in

Vorherige Seite

1/177

Nächste Seite

6.47 Multi-sequencer 110

The numbered gate buttons control the gate output signal. The output will generate a square

pulse of 1/8 of a quarter note with an amplitude of 1 Volt for each active gate buttons. To hear a

step, the gate button must be clicked (green light on). The loop buttons are used to set the length

of the Pattern from 1 to 16 steps.

Song Mode

The sequencer can play patterns individually or in a programmed order using a song. The song

mode is activated by placing the mode selector to song. The sequencer can hold 8 songs. A song

can hold up to 1000 events. The sequencer will loop each time a song ends. To make the sequencer

stop at the end of a song, the once button must be clicked.

Five parameters are associated with each pattern on the square display: pattern, primary loop

point (L), primary loop times (PRI), secondary loop times (SEC) and play mode (MODE). Each of

the parameters on the window is adjusted by clicking-holding and dragging. The keyboard arrows

can also be used once a parameter has been selected. The pattern parameter determines the pattern

to be played for a given event, from A1 to D8.The primary loop is a group of events that will be

played a number of times equal to the value of the primary loop times (PRI) parameter. In order

to program a primary loop of events, the beginning and the end of the loop must be selected by

the primary loop point parameter. This parameter has 3 values: none (-), start (S) and end (E).

Selecting start sets the return point of the loop to a given event and activates the primary loop times

parameter, which can be set from 1 to 99. Selecting end (E) in any subsequent event will make the

sequencer return to the start event until the number of loops is reached. Note that placing a primary

loop inside another one will not produce the desired effect. The secondary loop times parameter

sets the number of times an event will be played before switching to the next. It can be set from 1

to 99. The play mode parameter change the play mode of the sequencer. The sequencer will stay in

the selected play mode for the next events. In order to make song programming easier, use of the

play from position (PFP) button is useful. It allows to start the song from a selected event. When

clicked, the ﬁrst event in the edit window will be remembered as the ﬁrst and return event of the

song.

Editing a song

The song info window at the top of the event window displays the event currently being played or

selected with the wheel located at the right of the event window. Events can be removed from a

song by clicking on the “-” button on the right of the song info window. Pressing on the “+” button

inserts a new event after the event currently selected.

Note: see also Control Voltage Sequencer, Control Voltage Sequencer with Songs, Single

Gate Sequencer, Single Gate Sequencer with Songs, Dual Gate Sequencer and Dual Gate

Sequencer with Songs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AAS Tassman 4 Seite 110

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info