Bedienungsanleitung Abon 433 MHz Remote Key-pad 2009 (Seite 8 von 19) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

680515

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

Read the operating instructions

carefully before installing and

commissioning. Keep the operating

instructions handy for future use.

Product description

The remote key-pad for mounting externally

can control 4 different self-learning 433 MHz

receivers. Three radio signals are protected

with individually programmable 1-6 digit

numeric codes. Once the correct numeric

code has been entered, any number of signals

can be sent. This repeat function can be

interrupted to enter a different numeric code

by pressing the key button. 8 seconds after the

last entry, the remote keypad is locked

automatically. All access codes can be

deleted using a reset function. 1 radio signal is

sent by pressing the ring-button (Bell symbol).

Note: If all 3 access codes are programmed,

reprogramming can only be done after

performing a reset.

Packaging

Only reusable materials are used. Dispose of

packaging in an environmentally-friendly way

and according to the legal guidelines in your

area.

Safety information

Improper or accidental operation of the

devices and functions controlled by the remote

key-pad must be prevented. Master and / or

access codes are not to be noted on the

remote key-pad. Mount the remote key-pad

outside of the reaching distance of children.

Ensure that the device to be controlled will

pose no hazard before every operation.

Intended usage, Guarantee

The manufacturer must provide written and

exclusive approval for:

•Modifications or attachments

•Repairs performed by persons or

businesses that have not be authorised by

the manufacturer

If this approval is not granted, the guarantee

and warranty can become void. No liability can

be assumed for damages that result from not

observing the information in the operating

manual.

Instructions

for installation, programming, operation and

resetting the remote key-pad can be found

starting on page 14.

Service and maintenance

Do not use acidic or paint-dissolving cleaning

solvents.

Battery replacement

If the battery capacity is too low, the keypad

lighting flashes and is then turned off.

Removing the battery: See installation from

page 14.

Technical data

Removal, Disposal

Removing the remote key-pad is

performed in the opposite

sequence to that in the installation

instructions. Dispose of the device

according to environmental

guidelines.

EU Declaration of conformity

The described remote key-pad conforms with

all basic requirements according to Article 3 of

R&TTE 1999/5/EG. The following provisions

and standards were utilised:

EN 60950 / EN 300 220-1/-3, EN 301 489-1/-3

Cardo Door Production GmbH

Normstahlstraße 1-3

D-85368 Moosburg

Dr. Wolfgang Schulz Executive director

02.01.2009

Power supply 9V battery

Transmission frequency 433 Mhz, 4 channels

Housing Plastic, Coated, IP55

Dimensions (WDH) 82 x 40 x 102 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Abon 433 MHz Remote Key-pad 2009 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info