Bedienungsanleitung Absaar HB-1204BS (Seite 12 von 43) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

588213

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

c. Clean battery terminals. Be careful to keep corrosion from coming in contact with eyes.

d. Add distilled water in each cell until battery acid reaches level specified by battery

manufacturer. This helps purge excessive gas from cells. Do not overfill. For a battery without

cell caps, carefully follow manufacturer's recharging instructions.

e. Study all battery manufacturers’ specific precautions such as removing or not removing cell

caps while charging and recommended rates of charge.

f. Determinate voltage of battery by referring to car owner's manual and make sure that output

voltage selector switch is set at correct voltage. If charger has adjustable charge rate, charge

battery initially at lowest rate.

7. CHARGER LOCATION

a. Locate charger as far away from battery as the DC cable permits.

b. Never place charger directly above battery being charged; gases from battery will corrode and

damage charger.

c. Never allow battery acid to drip on charger when reading gravity or filling battery.

d. Do not operate charger in a closed-in area or restrict ventilation in any way.

e. Do not set a battery on top of charger.

8. DC CONNECTION PRECAUTIONS

a. Connect and disconnect DC output clips only after removing AC cord from electric outlet.

Never allow clips to touch each other.

b. Attach clips to battery and chassis

Follow these steps when battery is installed in vehicle. A spark near battery may cause battery

explosion. To reduce risk of a spark near battery:

a. Position AC and DC cords to reduce the risk of damage by hood, door, or moving engine

parts.

b. Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons.

c. Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has larger

diameter than NEGATIVE (NEG, N, -) post.

d. Determine which battery post is grounded {connected) to the chassis. If negative post is

grounded to chassis (as in most vehicles), see (e). If the positive post is grounded to the chassis.

e. For negative-grounded vehicle, connect POSITIVE (RED) clip from battery charger to

POSITIVE {POS, P, +) ungrounded post of battery. Connect NEGATIVE (BLACK) clip to

vehicle chassis or engine block away from battery. Do not connect clip to the carburetor, fuel

lines, or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine

block.

f. For positive-grounded vehicle, only connect NEGATIVE (BLACK) clip from battery charger

to NEGATIVE (NEG, N, -) ungrounded post of battery. Connect POSITIVE (RED) clip to

vehicle chassis or engine block away from battery. Do not connect clip to the carburetor, fuel

lines, or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine

block.

h. See operating instructions for length of charge information.

Follow these steps when battery is outside vehicle. A spark near battery may cause battery

explosion. To reduce risk of a spark near battery:

a. Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has larger

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Absaar HB-1204BS Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info