554031
20
Zoom out
Zoom in
Vorherige Seite
1/96
Nächste Seite
6-20
6.7 What are the effects of the different jumper settings?
The PC board of the ABUS wireless alarm system is fitted with internal jumpers. Configure the jumpers according to the function
required as shown in this table:
Jumpers on the
mainboard
Position Function
The
J9 jumper of the ABUS wireless alarm system is used for restoring the
default factory settings of your alarm system.
To restore the factory settings, plug the jumper plug on to both pins of the
jumper. Switch off all electricity to the system and wait at least 10 seconds.
Reconnect the power supply. The factory settings are restored. You can then
take off the jumper plug and plug it on to one pin.
IMPORTANT: Restoring the factory settings is possible only if it was
enabled in the installer menu.
Restores the factory
settings.
(J9)
(Default)
The default position of the jumper plug
Jumper
J10 of the ABUS wireless alarm system is used for selecting
between rechargeable batteries and normal batteries. If the jumper plug is
plugged on to both pins, the batteries are recharged.
IMPORTANT: As this is not the factory settings, this jumper position
must be changed.
Rechargeable battery
(J10)
(Default)
Use this setting for batteries that cannot be recharged.
Jumper J6 of the ABUS wireless alarm system activates/deactivates the
battery discharge protection. If the jumper plug is placed on to one pin, your
alarm system switches off automatically if the battery voltage falls below 6.3V
DC to avoid excess discharge.
NOTE:
With this setting, your alarm system first starts to operate when power is
available from the power supply unit.
Battery protection
(J6)
(Default)
The battery discharge protection is deactivated, i.e., the battery can
be completely discharged if there is a mains power failure, so that
the batteries have to be replaced.
NOTE:
With this setting, alarm system first starts to operate when the batteries are
inserted.
Jumpers on the
base plate
Position Function
UO 1 (J5)
or
UO 2 (J5)
(Default)
Defines the function of switch output 1 and switch output 2, as described in
the section “wired utility outputs” on page 5-17.
Default:
1 pin
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Abus FU9000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Abus FU9000

Abus FU9000 Installationsanweisung - Deutsch - 96 seiten

Abus FU9000 Bedienungsanleitung - Deutsch - 55 seiten

Abus FU9000 Bedienungsanleitung - Englisch - 56 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info