756353
13
Zoom out
Zoom in
Vorherige Seite
1/74
Nächste Seite
External I/O connections and wiring
13
Alarm inputs
The alarm inputs on the recorder are used for event
control via externally wired detectors (door contacts,
motion detector, smoke detector, light barriers, etc.). On
the recorder side, the inputs can be used to activate a
recording, alert via CMS or send an alarm email, among
other things. The alarm inputs are purely switch contacts
(Normally Open/Normally Closed) which must not be
voltage controlled.
Note
Following the connection of the detector to the
alarm input of the recorder, the behaviour in the
normal state (NO/NC) and the event reaction must
be programmed in the settings menu.
Alarm outputs
The alarm outputs on the recorder are used for the action
control of externally wired devices/actuators (sirens,
lamps, door openers, etc.). The alarm output switching
takes place via integrated relays on the recorder. In order
to prevent damaging the relay/recorder, the device’s
maximum switching power must not exceed the specified
values of 12 V / 1 A.
Note
After the actuator has been connected to the
alarm input of the recorder, the event reaction
must be programmed in the settings menu.
RS-485 output (NVR10030/NVR10040)
The RS-485 output on the recorder is used to control
analogue PTZ cameras.
IP cameras with an integrated PTZ function are fully
controlled via the network.
The use of the interface is intended as an alternative for
the use of IP cameras with external motor control.
Connection
Description
Depending on the recorder model,
1–16 inputs are available. First,
plug the detector contact in an
open input (IN1-16) and then
connect the grounding contact (G).
Connect more detectors in the
same way:
IN1 G
IN2 G
IN3 G
….
IN16 G
It does not matter whether you
connect all detectors to one
grounding contact or divide them
up among the available contacts.
Use terminal blocks in order to
connect multiple detectors to one
grounding contact.
Co
nnection
Description
Depending on the recorder model,
1–8 outputs are available. First,
plug the actuator/device in an
open output (OUT1-8) and then
connect the grounding contact (G).
Connect further actuators in the
same way:
OUT1 G
OUT2 G
OUT3 G
….OUT8 G
It does not matter whether you
connect all actuators to one
grounding contact or divide them
up among the available contacts.
Use terminal blocks in order to
connect multiple actuators to one
grounding contact.
Connection
Description
Connect the PTZ control by using
the Transmit and Receive pins.
Only available on
NVR10030/NVR10040 !
Detector
s
Actuator
_
_
-
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Abus nvr10030 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Abus nvr10030

Abus nvr10030 Bedienungsanleitung - Deutsch - 75 seiten

Abus nvr10030 Bedienungsanleitung - Holländisch - 74 seiten

Abus nvr10030 Bedienungsanleitung - Dänisch - 74 seiten

Abus nvr10030 Bedienungsanleitung - Französisch - 76 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info