Bedienungsanleitung Abus RM15 (Seite 14 von 41) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

643726

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

– 26 – – 27 –

1. Loosen the smoke detector from the base of the housing by turning it

anticlockwise. Mark the drill holes through the base.

2. Drill the holes, put in the plugs and screw in the base.

3. Insert the battery (see the diagram ) and fasten the smoke detector by twisting

it clockwise onto the base. The detector has a safety device that prevents

installation without a battery.

4. If you cannot fasten the smoke detector to the base:

Check whether the battery is correctly inserted and connected.

Operation and function (test)

• The smoke detector is ready for use as soon as you put in the battery.

• Under the housing cover there is an indicator lamp which ashes every

32 seconds to show that the battery is correctly inserted and is delivering enough

power to generate an alarm.

• Check the function of the smoke detector at regular intervals. Press the lower

section of the housing cover for 5 seconds. If you hear a signal, the device is

working properly and can be fastened.

• Alternatively, you can use the RM test spray available from ABUS to test the smoke

detector. If the RM test spray enters the detection chamber, an alarm should

sound, so that you can test whether the detector is working properly.

Replacing the battery

• If the battery is low, the smoke detector beeps once every minute (for up to

30 days) to remind you to replace the battery.

• You must change this battery when you hear this signal.

• Even so, the smoke detector remains functional in this condition.

• You must test the smoke detector each time you change the battery.

• Carry out the test as detailed above.

Putting into operation

Note

To ensure a long service life and reliable operation, we recommend using

the following high-quality batteries:

• RM10 VdS: Alkaline 9V block battery Duracell MN1604 or Energizer 255

• RM15 VdS: Lithium 9V block battery EVE CR9V/P or Ultralife U9VL-J-P

Alarms and error signals

When the alarm threshold is exceeded, a loud alarm sounds.

• The alarm continues sounding as long as there is smoke in the detection chamber.

• The alarm is only switched o when there is no more smoke in the detection

chamber.

What to do if there is a false alarm?

A false alarm can occur due to very high air humidity, the build-up of smoke whilst

cooking or a large build-up of dust, for example.

• If the alarm sounds, rst get yourself to safety. If you are certain that it is a false

alarm, you can disassemble the detector and disconnect the battery.

• The smoke detector will switch o automatically once the smoke particles have

le the smoke chamber inside the detector.

Note

• Protect the device from dust, dirt and moisture.

Putting into operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Abus RM15 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info