Bedienungsanleitung Acoustica Mixcraft-4 (Seite 40 von 93) (Englisch)

541323

Zoom out

Zoom in

Vorherige Seite

1/93

Nächste Seite

Choose Adjust Pitch By from the drop down list on the Sound Details Tab.

This allows you to change the pitch by semitones. You can type in a partial amount such as 1.26 semitones or use

the drop down or spin arrows to adjust by a whole semitone or 1/10th of a semitone. You might use this option to

fix a slightly off key vocal performance or transpose a sound into a key you are more familiar with.

Adjust To Project Key

Click here for more on adjusting a sound's key.

Transposing Virtual Instrument Clips

You can transpose a Virtual Instrument Clip by clicking on the Sound Details tab on the bottom of the window.

Click on the drop down entitled Adjust To Project Key and choose Transpose By.

Then either type in or select the number of half steps that you'd like to transpose the clip by.

Virtual Instrument clips can be transposed without audio degradation because each time they are played the

synthesizer recreates the sound from the MIDI data.

Adjusting The Sound's Key

You can change a sound's key by clicking the Sound Details Tab on the bottom of the window. Each sound can be

in one of the following modes: Adjust To Project Key, Adjust Pitch By, Transpose By (Virtual Instrument clips only)

or Do Not Fix Pitch. (Audio clips only) Select the drop down to change the mode to Adjust to Project Key.

Adjust To Project Key

If in this mode, Mixcraft will adjust the pitch of the sound based on the difference between the project's key and the

sound's key. For example, if the project key was F# and the sound's key was F, it would adjust the pitch of the

sound up by one semitone so that it was in tune with F# instead of F.

However, you can have more than one key change in a project. A sound in Adjust To Project Key mode will adjust

to the correct # of half steps in order to play in the correct key based on the most recent key change. To continue

the example, if your sound was in F and you had two key changes to A and then G, it would correspond to shifting

the pitch of your sound by four semitones up to A and then by two semitones up to G.

The software adjusts the pitch by the shortest distance between two keys. For example, if the project key was G

and the sound's key was F, it will adjust it by +2 semitones, instead of -10 semitones.

Changing The Key Of A Sound

ssuming that the key of the sound is correct, you can change the key of a sound by adding markers with key

changes and/or by changing the project's key. You do not need to change the key of the sound on the Sound

Details Tab, but, instead, you should change the project key or add key change markers! In short, if you want to

change the key of a sound, change the project key! Changing the key of a sound should only be done if the

detected key is wrong!

Changing The Detected Key Of A Sound

You must be in

djust To Project Key mode to change the detected key of a sound.

Page 40 of 93Mixcraft 4

2/7/2008file://C:\acoustica\mixcraft\hel

\flat-manual\mixcraft.htm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Acoustica Mixcraft-4 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info