Bedienungsanleitung ACP MCS10DSE (Seite 13 von 17) (Englisch)

660223

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

Digital Dial Operation

Digital Dial option is available on some models only.



Oven Wall Clearances

A—For North American (UL/CSA) models, allow

at least 2” (5.1 cm) of clearance around top

of oven. For International (50 Hz) models,

allow at least 12” (30 cm) of clearance

oven cools electrical components. With

properly and life of electrical parts is

reduced.

B—Allow at least 2” (5.1 cm) between air

discharge on back of oven and back wall.

C—Allow at least 2” (5.1 cm) of clearance around

sides of oven.

No metal pans

DO NOT power spray

So...how do I use it? (Electronic / Mechanical Dial)

Heating

1. Open oven door, place food in oven, and close oven door.

2. Select desired power level or use default 100%.

2. Turn time entry knob clockwise to desired time.

• Cooking time can be set up to 10 minutes.

• Oven begins operation and time counts down.

3. When cooking time has elapsed, microwave energy stops and oven signal sounds.

Interrupting Operation

Open oven door to interrupt operation or turn time entry knob counterclockwise to “0”.

To resume microwave oven operation, close door, select power level pad, and turn knob.

Changing Time and Canceling Mistakes

Heating time and power level can be changed at any time while the oven is operating.

Press power level pad or turn knob to desired new setting. To set cooking time to zero,

turn knob counterclockwise to “0” or cycle door open and closed.

2:00

1:00 - 2:00

:30

:15

:45

1:30 - 2:30

Menu Guide

20% 50% 70% 100%

20%

70% 100%

50%

Changing Timer Option

Timer resetting to zero can be set at any time to pause current cook time and power level when door is

opened. To change this option follow the step below.

• With door open press and hold the 100% pad

100%

for 5 seconds until beep is heard. Close the

door this changes timer setting to pause current cook time and power level when door is opened.

Timer pausing current cook time and power level can be set at any time to reset to zero and 100%

power level when door is opened. To change this option follow the step below.

• With door open press and hold the 20% pad

20%

for 5 seconds until beep is heard. Close

the door this changes timer setting to reset timer to zero and power level to 100% when door is

opened.

The switching operation of this microwave oven can cause voltag der unfavorable voltage

supply conditions can have adverse effects. This device is intended for the connection to a power supply system with a maximum permissible system

impedance Zmax of 0.2 Ohms at the interface point of the user’s supply. The user has to ensure that this device is connected only to a power

the interface point.

Oven Wall Clearances

A—Allow at least 2” (5.1 cm) of clearance around top of

oven. Proper air ow around oven cools electrical

components. With restricted air ow, oven may not

operate properly and life of electrical parts is reduced.

B—There is not an installation clearance requirement for the

back of the oven.

C—Allow at least 1” (2.54 cm) of clearance around sides of

oven.

D—Install combination oven so oven bottom is at least 3

feet (91.5 cm) above oor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ACP MCS10DSE Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ACP MCS10DSE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info