Bedienungsanleitung ACP RFS518TS (Seite 10 von 17) (Englisch)

660227

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

Programming Keys

Oven is shipped from the factory for single key programming. To change

the oven default to allow double key programming, see User Option

section. To change the amount of time or the power level for a preset key:

1. Open oven door.

• READY displays.

• If door is closed or STOP key is pressed before programming is complete,

changes are discarded and microwave exits programming mode.

2. Press and hold key 1 for approximately 5 seconds.

• This begins programming mode.

• Microwave will beep and PROGRAM displays. Oven is in

programming mode.

3. Press key to be reprogrammed.

• Press two keys if reprogramming a double pad program.

• Power level and cooking time display.

• If power level does not display, microwave is set to full power.

4. Enter cooking time by using the number keys.

5. Press a power level key to change power level if desired.

6. Press START key to save new programming changes to the key.

• PROGRAM displays.

• If START is not pressed, changes will not be saved.

7. Press STOP/RESET key or close oven door to exit

programming mode.

Programming the Oven Control (Electronic Control)

Programming Multiple Stages

Stage cooking allows consecutive cooking cycles without interruption.

Up to four dierent cooking cycles can be programmed into a memory key.

To use stage cooking:

1. Follow steps 1 through 5 above.

6. Press TIME ENTRY key.

• Display briey shows the key number that is being programmed and

the stage number to the upper right.

• Display changes to cook time and power level for the next stage.

7. Enter cook time and power level as in steps 4 and 5.

• To enter another cooking stage for that key, press

TIME ENTRY key again.

• Up to four dierent stages can be programmed.

8. Press START key to save new programming changes to the key.

9. Press STOP/RESET key or close oven door to exit programming

mode.



PROGRAM.

When set to single key or

double key programming,

the display will show PROGRAM

when programming keys for single

or double digit cooking sequenses.

To change the oven’s default to

allow either single key or double key

programming, see the User Option

section.

QTY X2

Programming

This feature allows a preset

percentage of original cook

time, called a cooking factor, to

be added to a cook sequence.

To change the cooking factor:

1. Open oven door.

2. Press and hold key 1 for

approximately 5 seconds.

3. Press key to be reprogrammed.

4. Press the QTY X2 key.

5. Press a numbered key to

change the cooking factor.

• Cooking factor can be set

from 10% to 100%.

• Default is 80%.

• Key 5 would change the

cooking factor to 50%.

• Key 3 would change the

cooking factor to 30%.

6. Press START key to save

changes.

Canceling Mistakes

If oven is not cooking, press

STOP/RESET key to clear

display. If oven is cooking,

press STOP/RESET key once to stop

oven, then again to clear display. If

oven door is open and time shows in

display, close oven door and press

STOP/RESET key to clear display.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ACP RFS518TS Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ACP RFS518TS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info