Bedienungsanleitung Acronis Access (Seite 11 von 105) (Englisch)

624412

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

 Address - The DNS name or IP address of your File Repository or pick All Addresses to listen on

all interfaces. If you specify an IP or DNS address, the same address should also be specified in

the File Repository section of the web interface. For more information on it, visit the File

Repository article.

 Port - The port of your File Repository. The same port should also be specified in the File

Repository section of the web interface. For more information on it, visit the File Repository

article.

 File Store Path - UNC path to your File Store. If you change the File Store path, you MUST

manually copy any files that are already in the original File Store location to your new location.

Note: If you move the File Store to another location, you should upload a new file to make sure it is

going into the correct new location. Another thing is downloading a file that was already in the file

store to make sure all of the files that were in the original location can be accessed at the new location.

 Service Account - If the file storage for the repository is on a remote network share, then the

service account should be configured to be one that has permissions to that network share. This

account must also have read and write access to the Repository folder (e.g. C:\Program Files

(x86)\Acronis\Access\File Repository\Repository) to write the log file.

After you have filled in all the necessary fields, pressing Apply or OK will restart the services you have

made changes to. It will take 30-45 seconds after the services have started before the Acronis Access

Server is available. At this point, a web browser will automatically launch and connect to the Acronis

Access's IP address and port. On the login page, set the administrator password and then the Setup

Wizard (p. 11) will guide you through the setup process.

Note: Write down the administrator password, as it cannot be recovered if forgotten.

Note: If you need to change any of the network IP addresses/ports or certificates used by the Acronis Access

components, you can run the Configuration Utility again at any time to make these changes. It will

automatically adjust the necessary configuration files and restart the services for you.

1.4 Using the Setup wizard

After installing the software and running the configuration utility to setup network ports and SSL

certificates, the administrator now needs to configure the Acronis Access server. The Setup Wizard

takes the administrator through a series of steps to get the basic functionality of the server working.

Note: If you are upgrading from activEcho or mobilEcho, please read the Upgrading (p. 17) section before

continuing.

Note: After the configuration utility has run, it will take 30-45 seconds for the server to come up the first time.

Navigate to the Acronis Access's web interface using the IP address and port specified in the

configuration utility. You will be prompted to set the password for the default administrator account.

Note: Administrators can be configured later on, for more information visit the Server Administration section.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Acronis Access Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Acronis Access

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info