Bedienungsanleitung Acronis Backup PC 11.7 (Seite 175 von 248) (Englisch)

624440

175

Zoom out

Zoom in

Vorherige Seite

1/248

Nächste Seite

2. Select the NIC that provides access to the local area network that includes the required VLAN.

3. Specify the VLAN identifier.

After you click OK, a new entry appears in the list of network adapters.

If you need to remove a VLAN, click the required VLAN entry, and then click Remove VLAN.

9.3 Working under bootable media

Operations on a machine booted with bootable media are very similar to backup and recovery under

the operating system. The difference is as follows:

1. Under a Windows-style bootable media, a volume has the same drive letter as in Windows.

Volumes that do not have drive letters in Windows (such as the System Reserved volume) are

assigned free letters in order of their sequence on the disk.

If the bootable media cannot detect Windows on the machine or detects more than one of them,

all volumes, including those without drive letters, are assigned letters in order of their sequence

on the disk. This way, the volume letters may differ from those seen in Windows. For example,

the D: drive under the bootable media might correspond to the E: drive in Windows.

Be careful! To be on the safe side, it is advisable to assign unique names to the volumes.

2. The Linux-style bootable media shows local disks and volumes as unmounted (sda1, sda2...).

3. Backups created using bootable media have simplified file names (p. 53). Standard names are

assigned to the backups only if these are added to an existing archive with standard file naming,

or if the destination does not support simplified file names.

4. The Linux-style bootable media cannot write a backup to an NTFS-formatted volume. Switch to

the Windows style if you need to do so.

5. You can switch the bootable media between the Windows style and the Linux style by selecting

Tools > Change volume representation.

6. There is no Navigation tree in the media GUI. Use the Navigation menu item to navigate

between views.

7. Tasks cannot be scheduled; in fact, tasks are not created at all. If you need to repeat the

operation, configure it from scratch.

8. The log lifetime is limited to the current session. You can save the entire log or the filtered log

entries to a file.

9.3.1 Setting up a display mode

For a machine booted from media, a display video mode is detected automatically based on the

hardware configuration (monitor and graphics card specifications). If, for some reason, the video

mode is detected incorrectly, do the following:

1. In the boot menu, press F11.

2. Add to the command prompt the following command: vga=ask, and then proceed with booting.

3. From the list of supported video modes, choose the appropriate one by typing its number (for

example, 318), and then press ENTER.

If you do not wish to follow this procedure every time you boot from media on a given hardware

configuration, re-create the bootable media with the appropriate mode number (in our example,

vga=0x318) typed in the Kernel parameters window (see the Bootable Media Builder (p. 167) section

for details).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Acronis Backup PC 11.7 Seite 175

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Acronis Backup PC 11.7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info