Bedienungsanleitung Acronis disk director suite 10 (Seite 44 von 96) (Englisch)

284412

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

To perform the pending operation you will have to commit it (p. 20). Exiting the program without

committing the pending operations will effectively cancel them.

5.24 Unhiding a volume

This operation applies to hidden volumes on basic MBR disks.

Unhiding a hidden a volume means changing the volume type so that it will be visible by the

operating system. You may want to unhide a volume in order to:

 Make a previously hidden volume again visible to the operating system.

 Access data and make changes to files stored on a hidden OEM volume.

To unhide a volume

1. Right-click the hidden volume you need to unhide, and then click Unhide volume. The program

automatically assigns the first vacant drive letter to this volume.

2. Click OK to add the pending volume unhiding operation.

The results of the pending operation are immediately displayed as if the operation had been

performed.

To perform the pending operation you will have to commit it (p. 20). Exiting the program without

committing the pending operations will effectively cancel them.

5.25 Specifying i-node density

This operation applies to volumes whose file systems are Ext2 or Ext3.

The i-node is the main data structure for Linux Ext2/Ext3. All of a files information, with the

exception of its actual name and data, is stored in the i-node. Each file has its own i-node. Each i-

node contains a file description, including number, file type, size, data block pointers, etc. Space for i-

nodes is allocated when you install the operating system or when a new file system is created. The

maximum number of i-nodes, and hence the maximum number of files, is set at file system creation.

Running out of i-nodes prohibits the creation of additional files and directories on the volume even if

there is sufficient disk space. I-nodes themselves consume disk space, so specifying the i-node

density lets you organize disk space in the optimal way. I-node density is determined by specifying

the number of bytes per i-node. Usually, the default value is 4096 bytes per i-node.

Important: If you change the i-node density of a boot volume the operating system will become unbootable. To

restore the system bootability use a boot loader.

To specify i-node density

1. Right-click the Ext2/Ext3 volume, and then click Change i-node density.

2. In Bytes per i-node, specify the required value.

 Use lower i-node density (that is, increased Bytes per i-node value) for a volume that

contains just a few large files. This will allocate more space for files and less for i-nodes. The

less i-nodes there are the in the system, the faster the “file system check” operation will be

performed.

 Use higher i-node density (that is, reduced Bytes per i-node value) for volumes that contain a

large number of small files. This will allocate more space for i-nodes and less for data. The

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Acronis disk director suite 10 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Acronis disk director suite 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info