624429
27
Zoom out
Zoom in
Vorherige Seite
1/38
Nächste Seite
Appendix A Hard disks and BIOS setup
Copyright © Acronis, Inc., 2000–2004
27
A.1.3 Installation modes, jumpers
1. A hard disk can be installed in a computer as
master or as slave. The mode of
hard disk installation is defined by the position of special connectors (called
jumpers) on the hard disk.
The jumpers are either located on the electronic board of the hard disk or a special
socket that provides for the connection of the hard disk and the motherboard.
There is usually a sticker on the drive that explains the markings. Typical markings are
DS, SP, CS and PK.
Each jumper position corresponds to one hard disk(s) installation mode:
DS – master/factory default
SP – slave (or no jumper required)
CS – cable select for master/slave: the purpose of the hard disk is determined by
its physical position with respect to the motherboard
PK – jumper parking position: the position where one can put the jumper if it is
not necessary in the existing configuration
The hard disk with the jumper in master position is treated by the basic input/output
system (BIOS) as bootable.
The jumpers on hard disks that are connected to the same cable can be in the cable
select for master/slave position. In this case, BIOS will deem as «master» the disk
that is connected to the IDE cable closer to the motherboard than the other one.
Unfortunately, hard disk markin
s were never standardized. You mi
ht well find that markin
s
on your hard disk differ from the ones described above. Moreover, for the older types of hard
disks, their purpose could be defined by two jumpers instead of one. You should study the
markings carefully before installing your hard disk in the computer.
It is not enough to physically connect the hard disk to the motherboard and set the
jumpers properly for the hard disk to function — hard disks have to be properly
configured with the motherboard BIOS.
27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Acronis MigrateEasy 7.0 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Acronis MigrateEasy 7.0

Acronis MigrateEasy 7.0 Bedienungsanleitung - Deutsch - 37 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info