Bedienungsanleitung Acronis True Image 11 Home (Seite 112 von 121) (Englisch)

624453

112

Zoom out

Zoom in

Vorherige Seite

1/121

Nächste Seite

Appendix B. Hard disks and BIOS setup

The appendices below provide you with extra information on the hard disk

organization, how information is stored on disks, how disks should be installed in

the computer and plugged into the motherboard, configuring disks with BIOS,

partitions and file systems, and how operating systems interact with disks.

B.1 Installing hard disks in computers

B.1.1 Installing a hard disk, general scheme

To install a new IDE hard disk, you should do the following (we will assume you

have powered OFF your PC before you start!):

1. Configure the new hard disk as slave by properly installing jumpers on the

board of its controller. Disk drives generally have a picture on the drive that shows

the correct jumper settings.

2. Open your computer and insert the new hard disk into a 3.5’’ or 5.25’’ slot

with special holders. Fasten down the disk with screws.

3. Plug the power cable into the hard disk (four-threaded: two black, yellow and

red; there is only one way you can plug in this cable).

4. Plug the 40- or 80-thread flat data cable into sockets on the hard disk and on

the motherboard (plugging rules are described below). The disk drive will have a

designation on the connector or next to it that identifies Pin 1. The cable will have

one red wire on an end that is designated for Pin 1. Make sure that you place the

cable in the connector correctly. Many cables also are “keyed” so that they can only

go in one way.

5. Turn your computer on and enter BIOS setup by pressing the keys that are

displayed on the screen while the computer is booting.

6. Configure the installed hard disk by setting the parameters type, cylinder,

heads, sectors and mode (or translation mode; these parameters are written on the

hard disk case) or by using the IDE autodetection BIOS utility to configure the disk

automatically.

7. Set the boot sequence to A:, C:, CD-ROM or some other, depending on where

your copy of Acronis True Image Home is located. If you have a boot diskette, set

the diskette to be the first; if it is on a CD, make the boot sequence start with CD-

ROM.

8. Quit BIOS setup and save changes. Acronis True Image Home will

automatically start after reboot.

9. Use Acronis True Image Home to configure hard disks by answering the

wizard’s questions.

10. After finishing the work, turn off the computer, set the jumper on the disk to

the master position if you want to make the disk bootable (or leave it in slave

position if the disk is installed as additional data storage).

B.1.2 Motherboard sockets, IDE cable, power cable

There are two slots on the motherboard to which the hard disks can be connected:

primary IDE and secondary IDE.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Acronis True Image 11 Home Seite 112

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Acronis True Image 11 Home

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info