Bedienungsanleitung Acson NET3-0808 (Seite 6 von 44) (Englisch)

646707

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

ENGLISH

iv) Set Event 3 Timer via remote control (Optional)

This timer can be controlled separately through remote control as well as ON TIMER or

OFF TIMER keys. Timer 3 can be set like timers 1 and 2 like above except the DAY setting

is not provided as this timer setting is valid everyday. An indicator ‘3’ will display during the

Event 3 timer setting mode. ‘ ON’ or ‘ OFF’ will blink at 0.5 sec interval during the

timer setting. If there is no futher time related (DAY, HOUR and MINUTE) key is pressed,

the unit will quit from the timer setting mode.

The ON/OFF timer setting received from remote control will override the Event 3 timer

setting from the unit.

1.8 Activating and canceling timers

These timers will not triggered if the timer is not active. To activate the timers, press the TIMER

ACTIVE key unit “TIMER ACTIVE” appears on LCD. This symbol is to indicate Event 1, Event

2 and/or Event 3 timers are active. Pressing the same steps will deactivate the timers and

“TIMER ACTIVE” symbol will disappear.

Another method to cancel the timers setting is changed all the hour setting of the timers to null

one by one. When the setting is null, the LCD display --:--, then this respective timer will be

disable.

1.9 Key Lock

These key lock function to inhibit any setting change. Press the MINUTE key 3 times

consecutively will activate key lock function, “KEYLOCK” will be shown on LCD. Upon all the

keys are locked, only ON/OFF key and MINUTE key can be pressed. To cancel the key lock

function, press the MINUTE key 3 times consecutively, the word “KEYLOCK” disappear.

1.10 Fan Lock

When the DAY key is press 3 times consecutively within 1.5 sec, the fan symbol (shown

above) will disappear and fan key will be inhibited. Press the DAY key 3 times to cancel the fan

lock function.

1.11 Battery Backup

Battery backup is used to retain the RTC and 7-days programmable timer settings during

power down. For unit without battery backup, the default setting will be 12:00 am the timer

clear during power up.

2.0 ERROR INDICATOR

If any abnormal condition detected, an error code will be shown. When the transmission line

between the main board and the unit line is opened, an error code ‘EOP’ will be shown. For

those errors detected from main board, the format of error code will be as following:

DX System:

CW System:

Error 7 Segments

Room sensor missing/short E1

Indoor coil sensor missing/short E2

Outdoor coil sensor missing/short E3

Compressor overload E4

Outdoor abnormal compressor overload trip or gas leak E5

Condensate water pump fault E6

Error 7 Segments

Room sensor error E1

Pipe water sensor error E2

Water pump error E3

Pipe water temperature poor E4

Pipe water fault E5

1 OM-NET3-0808_EN 9/5/08, 12:00 PM3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Acson NET3-0808 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info