Bedienungsanleitung ACV ETech W 36 (Seite 4 von 30) (Englisch)

524608

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

E-Tech W : 664Y6500 • B

INTRODUCTION

DESCRIPTION OF THE SPECIFICATIONS

This wall hung electric boiler is available in 7 models:

• The models Single phase 09 and 15 are supplied with 230 V.

• The models Tri phase 09, 15, 22, 28 and 36 are supplied with 400 V.

The maximum power can be adjusted for all models by acting on

the switches on the control panel.

The maximum power can be adjusted for this models by acting on

the terminals bridges.

Adjustable power

MODELS MIN MAX

E-Tech W 09 - Single phase 5.6 kW 8.4 kW

E-Tech W 15 - Single phase 9.6 kW 14.4 kW

E-Tech W 22 - Tri phase 14.4 kW 21.6 kW

E-Tech W 22 - Tri phase 14.4 kW 28.8 kW

E-Tech W 36 - Tri phase 18 kW 36 kW

LINING

The boiler is protected by a steel lining that first of all undergoes a

degreasing and phosphation process before being lacquered and

burnt at 220°C.

HEATING BODY

The boiler heat exchanger is constructed from mild steel with welded

joints. It is hydraulic tested under a pressure of 4.5 bar (maximum

working pressure = 3 bar).

HEATING ELEMENTS

Immersion heaters, constructed from stainless steel Incoloy 800 and

mounted in the top of the boiler, provide the power source for the

Boiler.

EQUIPMENT

The boiler is equipped with all the necessary components to allow

direct connection to a heating system without the need for a feed

and expansion cistern. These components include; primary 10 litre

expansion vessel (suitable for a system water content of up to 160

litres), pressure and temperature gauge, safety valve, circulating

pump, low water pressure switch, control and high limit thermostats,

on/off and power level switches.

CONNECTION

The boiler is suitable for connection to most heating and hot water

systems, with a maximum working pressure of 3 bar and a maximum

temperature of 87°C. It can also be used in multiple boiler installations

allowing greater outputs to be achieved.

The boiler, and connection glands for both the main power supply

and optional external controls are provided, suitable for single or

three phase electrical supply depending upon boiler output required.

An internal 3 amp MCB is provided to protect the internal control

circuit, from which optional controls can be connected e.G. Internal

or external timeclock.

CERTIFICATION

The boilers have been manufactured to comply with the following

standards BS EN60335-2-35: 1998, BS EN55014-2:1997 and BS

EN50081-1-1: 1992.

LEGEND

1. Top cover

2. Brass pocket

3. Hand side panel

4. Cable gland

5. Control panel

6. Automatic air vent

7. Heating element

8. Heating body

9. Pressure safety valve

10. Rear panel

11. Water pressure switch

12. Expansion vessel connection

13. Heating return

14. Expansion vessel

15. Valve of expansion vessel

16. Circulating pump

17. Heating ow

18. Manual reset hight limit thermostat

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ACV ETech W 36 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ACV ETech W 36

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info