Bedienungsanleitung ACV Glass BL (Seite 17 von 28) (Englisch, Holländisch, Französisch)

771220

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

STARTING UP

Before starting up your appliance, it is necessary to bleed the boiler, the pipes and the faucets

completely because air can be present in them.

For this, before putting the boiler under voltage, fill up the appliance by opening the stopcock of

the safety group and by keeping one of the hot water taps open if there are several of them. Let

the water flow until it is perfectly clear.

Switch on the appliance. During warming up, the expansion of water may cause flow-out from the

safety group.

It is recommended that the various functions should be controlled at least once every year.

THERMOSTAT

The thermostat which allows holding the temperature of the volume of water can be adjusted

between 20

C and 65

In order to prevent the generation of legionella bacteria, the thermostat is factory-set to 65

The thermal security integrated into the thermostat helps avoiding all kinds of incidental

overheating.

Where the security thermostat switches off, the installation technician should first search the

trouble and realise troubleshooting and then switch the appliance on.

ADVICE FOR THE USERS

MAINTENANCE

Before doing any interventions on the appliance, disconnect the appliance from the electric supply.

The shielded resistance and the anode are mounted on the dismantling flange therefore they can

be accessed to easily.

In order to drain the boiler, close the stopcock (A) of the safety group, open the draining tap B,

then open the hot water tap.

In order that the protection against corrosion should be more efficient, the boiler is equipped with

an anode.

The longevity of the anode depends on the agressivity of water and the normal usage temperature.

We recommend you to examine the condition of the anode periodically at least two years after the

start-up.

If the diameter of the anode (which is 32 mm normally) is equal to or less than 10 mm even on

only one point, it is compulsory to replace theanode.

If the water is very hard, it is advised to remove the scale from the boiler every year:

- drain the appliance then take off the flange,

- take off the scale appearing in the form of mud or laminae from the bottom of the tank then

clean the thermostat and the heating elementcarefully.

Do not try to take off the scale adhering to the side-wall of the tank because it constitutes efficient

protection from corrosion.

We assume no liability for damages which arise from the user's failure to comply with these

instructions.

HYDRAULIC SECURITY GROUP

Each month, move all the taps and the safety valve but always take back.

- stopcock A to the open position.

- the draining tap B to the closed position.

Please, check also the proper functioning of the safety valve. (Owing to the expansion of water occurring after

heating, in general the flow should be observed at the opening of the valve)

ENG

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ACV Glass BL Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info