620411
13
Zoom out
Zoom in
Vorherige Seite
1/68
Nächste Seite
en
13
System Control - ACVMax: 660Y2800 • B
EN
FR
NL
ES
IT
DE
PL
RU
APPLIANCE DESCRIPTION AND OPERATION
CH & DHW Settings / Heating Settings (Cont’d)
Heating Settings
Outdoor Curve / Warmest Day 18°C
CH2/CV2 Circuit Enabled
CH2 Max. Setpoint 60°C
CH2 Min. Setpoint 27°C
Warm Weather Shutdown
O
Circulation Pump Permanent Disabled
Heating Settings
CH2/CV2 Circuit Enabled
CH2 Max. Setpoint 60°C
CH2 Min. Setpoint 27°C
Warm Weather Shutdown
O
Circulation Pump Permanent Disabled
CH Post Pump Time 5 min
CH Post
Pump Time
5 min
O 30 min
CH Post Pump Time sets how long the central heating circulators will continue to op-
erate at the completion of a heating call. Refer to “Pumps on page 32 to know which
pumps will continue to operate. Any call during the CH Post Pump Time will be ignored
until the post pump has completed. The CH Post Pump Time feature allows the heat re-
maining in the boiler at the completion of a call to be sent to the heating system, which
will improve the overall eciency of the system.
Press the LEFT or RIGHT buttons to adjust the CH Post Pump Time then press the OK
button to store the setting.
Default: 5 min
Heating Settings
CH2 Max. Setpoint 60°C
CH2 Min. Setpoint 27°C
Warm Weather Shutdown
O
Circulation Pump Permanent Disabled
CH Post Pump Time 5 min
Freeze Protection Enabled
Freeze Protection
Enabled
Disabled
The Freeze Protection menu allows the feature to be enabled and disabled. The built-in frost
protection mechanism activates the system pumps as soon as the ow temperature [NTC1
probe] drops below 7°C. As soon as the ow temperature is at 5°C, the burner starts up until the
ow temperature rises above 15°C. The pumps continue to run for around 10 minutes.
Press the UP or DOWN buttons to select Enabled or Disabled then press the OK button to
store the setting.
Enabled The Frost Protection feature protects the installation from freezing at a prede-
termined system ow temperature.
DisabledThe Frost Protection feature is disabled. Only the pumps operate.
Default: Enabled
Heating Settings
CH2 Min. Setpoint 27°C
Warm Weather Shutdown
O
Circulation Pump Permanent Disabled
CH Post Pump Time 5 min
Freeze Protection Enabled
Frost Protection Setpoint -30°C
Frost Protection
Setpoint
-30°C
-30°C 10°C
Frost Protection Setpoint allows to dene the outside air temperature at which the an-
ti-freeze function is activated (only available if an outdoor temperature sensor is connected).
The pumps are activated when the outside temperature drops below the threshold dened
in this menu.
Press the LEFT or RIGHT buttons to adjust the Freeze temperature Setpoint then press
the OK button to store the setting.
In order to enable the Prestige boiler to protect the whole system against freezing, all
the valves of the radiators and the convectors should be completely open.
Default: -30°C
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für ACV Prestige Solo wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info