Bedienungsanleitung ADB ME1163 (Seite 22 von 68) (Englisch)

461422

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

DOMINO 24 & 48 USER MANUAL

www.adblighting.com

User Manual - page 20

Issue 1.2

6. THEATRICAL MEMORIES

6.1 OVERVIEW

A Theatrical Memory List is a recorded list of memories. Minimum 500 memories may be

recorded in Theatrical Memory List. Fading from one memory to the next done by a dipless

X- fade. The X-fade is usually executed automatic but can be manually.

6.2 RECORDING THEATRICAL MEMORY

To record a theatrical memory, create the desired look on the output, then press [record

memory].

The Record memory button flashes and the display scrolls “

Pick memory Number” and

stops on the next memory number available. (E.g. M 017). The OK button and Function

button flash to show that they are active. The theatrical memory number can be changed by

the use of the wheel. The indication M 024 indicates empty theatrical memory, M:024

indicate used theatrical memory. Pressing [OK] will record the current output to the

theatrical memory indicated on the display. If the selected theatrical memory has already

been used, the display will read “WARNING memory exists – overwrite?” You now have two

options.

• To erase the existing theatrical memory and replace it with the current output either

press [OK]

• To pick another theatrical memory number use of the wheel and press [OK]

6.2.1 THEATRICAL MEMORIES NUMBERS (AND POINT THEATRICAL

MEMORIES)

Any theatrical memory number between 0.1 and 99.9 can be used. To select a point

theatrical memory number use the [<] and [>] to decrease or increase by 0.1.

6.3 FADE AND LINK TIMES

As each theatrical memory is recorded (above) you may set the fade IN and OUT times

Before pressing [OK] to record the theatrical memory, press [function] to cycle through the

fade IN time and fade OUT. When any of the time settings are indicated, rotate the EDIT

wheel to set the desired time. The maximum time is more than 16 minutes and the minimum

time is 0 seconds. When a time is set lower than 0 seconds, it reverts to rotating speed

fader.

If you do not enter a time then the default settings will be used. The default time is 5 second

for IN and OUT time. (You can change the default times with the “Setup Preferences”

function. See the “UTILITIES” section).

6.3.1 LINK TIMES

If a theatrical memory contains a LINK time, then when that theatrical memory is played,

its link time starts counting down. At the completion of the link time, the theatrical memory

list will automatically step to the next theatrical memory. If every theatrical memory has a

link time, then the theatrical memory list will play like a chaser, but with the following

differences.

• The duration of every step may be individually set by its link time.

• The in and out fade times of every step may be individually set.

Setting link times see chapter below, Editing a theatrical memory.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ADB ME1163 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ADB ME1163

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info