Bedienungsanleitung ADB ME1163 (Seite 41 von 68) (Englisch)

461422

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

DOMINO 24 & 48 USER MANUAL

www.adblighting.com

User Manual - page 39

Issue 1.2

11.8 EDITING A CHASER

“Edit” allows you to permanently change the speed, crossfade, mode and direction plus you

can add or delete steps, connect or disconnect the STL (Sound to Light) processors and edit

the contents of each step.

These changes are applied to the chaser and if the chaser is currently on a submaster, they

will also be applied to the submaster. If the chaser is faded up on stage you will see the

changes. If the chaser is not live on stage, its steps are displayed on the channel LED

indicators and on the optional SVGA monitor.

• To edit a chaser on a submaster, press [edit], [f/a].

• To edit a chaser in the Grab master, press [edit], [f/a]

• To edit a chaser in a different page, press [edit], [Bank B] [f/a]

The indicators in the channel f/a buttons show the channels of the running chaser. Their

intensity reflects the levels of the channels in each step.

• To control the SPEED, rotate the EDIT wheel.

• To change the CROSSFADE between steps, press [function] until both “in” & “out” LEDs

light, then rotate the EDIT wheel.

• To change the MODE or DIRECTION, use the 3 buttons below the EDIT wheel as

described above.

• To connect or disconnect a STL (Sound To Light or SyncoBEAT) from the chaser,

repeatedly HOLD [function] until the STEP number(s) are shown on the display and the

STL button LEDs flash. Whilst holding [function] tap either [STL1] or [STL2].

Press [yes] to connect or disconnect the selected STL. See the “STL and SyncoBEAT”

section for more details.

11.8.1 ADD A STEP

To add a step, first edit the chaser (above), then press [step/stop] to stop the chaser and

continue pressing to step the chaser to the step prior to the point where the new step is to

be added.

Press [add] then either;

• Create the look for the new step on the output and press [record scene]. or

• To add a submaster memory as a step, press; [Bank B] (optional), [f/a] (scene

number). or

If necessary press [>] or [<] to start the chaser again in the desired direction.

When finished editing press [edit].

All changes are automatically saved.

11.8.2 REMOVE A STEP

To remove a step, first edit the chaser (above), then press [step/stop] to stop the chaser and

continue pressing to select the step to be removed.

To remove the step, press [remove], [yes].

If necessary, press [>] or [<] to start the chaser again in the desired direction.

When finished editing press [edit].

All changes are automatically saved.

11.8.3 MODIFY A STEP

To modify the channel levels of a step, first edit the chaser (above), then press [step/stop] to

stop the chaser and continue pressing to select the step to be modified. Press [function]

until the “chan” LED indicator lights and the display reads;

“Pick channel to edit”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ADB ME1163 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ADB ME1163

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info