Bedienungsanleitung Ade BA 911 Dorothea (Seite 8 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

641818

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

There is a little push button next to the battery case at the bottom side of the scale for

country specific settings with the option to switch from kg = kilogram to lb = pound.

Please pay attention to use the scale under consideration of your country specific unit of

weight.

4. Programming / Enter of personal data

Before first time use your personal data like gender (female or male, sports or no sports),

body height and age must be programmed and saved under selected locations P1 – P8

(up to 8 persons). The enter keys are located below the display. To enter your personal

data please utilise the buttons: SET (on and save button),  (plus button),  (minus

button) and follow the particular points:

1. Press the SET-button. The display indicates a flashing “ P1” . To select your personal

location (P1 – P8), press the 

or  button. After the selection of your personal

location, press the SET-button to save the reading.

2. After you’ ve selected your personal location (e.g. P3), the symbol for gender starts to

flash. To select the requested gender ( male, female, or

male sports,

female sports), press the

 or  button. After the selection of your gender, press

the SET-button to save the reading.

3. After you’ ve selected your gender (e.g. female), the symbol for body height starts to

flash (default 165 cm). To enter your height, press the 

or  button. After the

selection for your height, press the SET-button to save the reading.

4. After you’ ve selected your body height, the symbol for age starts to flash (default 30

age). To enter your age, press the 

or  button. After the selection of your age,

press the SET-button to save the reading.

After input completion, the display indicates “ 0.0 kg” and a few seconds later, the scale

automatically powers off.

To enter personal data of further persons please repeat the steps listed below.

5. Weighing function (weight measurement only)

1. Switch on the scale by using the step-on-function. Just step on the scale. Remain

stationary on the weighing platform and do not hold you tight. After a few seconds,

your weight will be displayed.

2. Step off the scale after weighing. The scale will switch off automatically after a few

seconds.

3. If you remain on the weighing platform, the analyser scale automatically switches

into the measuring mode and starts the body analysing.

6. Body Analysis

An analysis is only possible in bare feet. Your personal data must be entered first (please

see page 4).

1. The scale contains a step-on-function and an automatic user recognition. Carefully

step on the stainless steel points (measuring units) of the scale in bare feet and remain

stationary. User recognition: If the scale cannot automatically recognise the user, the

display will indicate the next both most similar memory locations e.g. “ P1P2” . Please

select your personal memory location (where your personal data are stored) by using

the  or  key and remain stationary on the scale.

2. At first, your weight will be indicated on the display. Shortly after, while the analysis is

taking place, the signal “ o” starts to move twice on the display from left to right. After

completion of the measurement, your measured values will be shown as follows:

1. Your body fat in %

2. Your body water in %

3. Your muscle mass in %

4. Your bone mass in kg

Afterwards your measured values (weight, body fat, body water, muscle mass and bone

mass) will be shown in changes successively 3 times.

EXAMPLE:

Weight Measuring process Body Fat Body Water Muscle Mass

When you once used the scale, you will be able to get the readings of your last

measurement. This function allows you to follow the changes between your

measurements. For that press the 

or  button and choose your personal location. Now

the display indicates in changes successively the measured values of your last

measurement.

The body fat content is shown as the amount of stored fat as a percentage of total body

weight. There is no generally accepted set value as this varies significantly according to

gender (due to the different build) and age. Body fat is vital for basic body functions. It’ s

protecting organs, cushioning joints, regulating body temperature, storing vitamins and

serves the body as energy storage. As essential for women a minimum body fat

proportion between 10% and 13% and for men between 10% and 13% is requested -

with the exception of competitive athletes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ade BA 911 Dorothea Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info