Bedienungsanleitung Adler AD 1293 (Seite 4 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

799450

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

5. Before taking the kettle out of the base make sure it is switched OFF.

9. Regularly remove limestone sediment inside the kettle. Sediment may cause overheating of the kettle, shorten life cycle and cancel

guarantee. Use mixings available in household stores or apply citric acid.

BEFORE FIRST USE: Fill up the kettle with water, boil and pour. Repeat three times. To remove possiblefactory smell..

4 - handle 5 - base 6 - anti-calc filter 7 - control panel

1. Fill the kettle with water. Make sure that heating plate is fully immersed in water.Till minimum mark

13. The kettle is an electrical device and it is not designed to hold water or other liquids. After boiling, the water must be immediately

pour into another bowl. The water in the kettle after boiling can not stay longer than 10 minutes. Before each use, fill the kettle with

fresh water above the minimum and below the maximum level.

8. After boiling, time demanded for the thermostat to be ready is 2 minutes. After this time the kettle can be switched on again.

BASICAL OPERATION:

2. Place the appliance on flat, even and heat resistant surface.

1 - plastic lid 2 - lid opening switch 3 - housing

7. Keep lid closed during the boiling process. Or the kettle won't automatically switch off.

10. Switching empty kettle, or with insufficient level of water, will cause automate switching off the kettle. Wait till cool down the kettle,

pour enough water and after few minutes switch the kettle on.

6. The kettle can manually be switched off any time by ON/OFF switch (A) at.

A- ON/OFF B - Temperature regulation C - Dechlorination function D- Keep warm function

12.Code E1 on LCD display warns user when the device is not on the basis of, or is not put properly.

Press the “A” key briefly, with the sound “di.”, it starts working. The LED (A) will flash.

DESCRIPTION

3. Plug the kettle to the 220-240V ~50/60Hz mains, press ON/OFF (A) switch. Indicator lamp will light.(A)

11 When the water is heated to the appropriate temperature, device signals this with two beeps.

SINGLE BOILING UP TO 100℃

After the water boils, indicator turns off and the buzzer sends out a “di di” sound at the same time.

To stop cooking, press the button (A) ON/OFF

USING THE ELECTRIC KETTLE

4. After boiling water the kettle will automatically switch off.

14. Holding down the button (A) for 3 seconds will turn off (OFF on the LCD display) the kettle, the LED (A) will flash.

23. Never switch on kettle without water.

24. Never use kettle without filter or with open cover (automatic shutdown will not work).

28. Do not wash the base of the kettle directly in the water, just wipe with a dry cloth.

25. Descale your kettle regularly. Using kettle with heating element covered by scale may

cause damage.

22. Never fill kettle above MAX level and below MIN level. It may cause damage of kettle.

27. The device is not designed to work with external schedulers or separate remote

control system.

26. Do not use aggressive detergents to wash the kettle housing - they can damage the

kettle or remove the markings.

29. Children aged 3 to 8 years old can enable and disable the device only when it is in its

normal position of use, they are supervised or instructed on the safe use and understand

the resulting risks. Children aged 3 to 8 years old can not connect device, operate, clean

or maintain.

lid. Do not open the lid during boiling in kettle or immediately after boiling, because steam

coming out of lid can cause burns.

21. Move the kettle only by holding it by handle..

ADVANCED OPERATION:

Press “A” key, the buzzer will send out a “di” sound, the kettle will start boiling now, the LED (A) will flash.

After that Press “D”,with the buzzer sends out “di” sound, “D” button indicator light is on, and the kettle is in keep warm mode. The

indicator”D” light is still lit after water has finished the boiling and the kettle automatically. The keep warm function for 2 hours. When

switches to the water temperature decreases to 90℃ the kettle starts to boil again to 100℃ and repeats the operation for 2 hours.

To stop the keep warm function press the button (A)

To stop, press the button (A)

After that Press“B” key once / twice / thrice / fourth /fifth / sixth /seven times, then the LCD display will show 40℃ / 50℃ / 60℃ / 70℃ /

80℃ /90℃ This means that it will stop heating when the water temperature reaches 40℃ / 50℃ / 60℃ / 70℃ / 80℃ /90℃

WATER BOILING 40℃ - 90℃ WITHOUT THE KEEP WARM FUNCTION

Press the “A” key briefly, with the sound “di.”, it starts working. The LED (A) will flash.

KEEP WARM FUNCTION 100℃

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Adler AD 1293 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info