Bedienungsanleitung Adler AD 2831 (Seite 5 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

799592

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

14.In order to provide additional protection, it is recommended to install residue current

device (RCD) in the power circuit, with residual current rating not more than 30 mA.

Contact professional electrician in this matter.

15.If using the device in bathroom after use remove the power plug from the socket,

because water proximity presents risk, even if the device is turned off.

16. Do not allow the device or power adaptor to wet. If the device falls into water,

immediately remove the power plug or power adaptor from the socket. If the device is

powered, do not put hands in the water. Have the device checked by the qualiﬁed

electrician before using it again.

17. Do not touch the device or power adaptor with wet hands.

18. The device has to be turned off after every use.

19. Do not leave switched on equipment or adapter without supervision.

20. Never use this device close to water, e.g.: Under shower, in bathtub, or above sink

ﬁlled with water.

21. If the device utilises a power adaptor, do not cover it, because this can cause a

dangerous temperature rise and can damage the device. Always connect the power

adaptor cable to the device, and then connect the power adaptor to the power socket.

22. The cutting scissors are very sharp. Use caution when assembling, dismantling and

cleaning. Do not touch any elements of the moving blade during the operation!

23.DO NOT CHARGE THE BATTERY FOR LONGER THAN 48 HOURS – this can cause

irreversible damage to the battery.

24. The charging process should be conducted in temperatures between 5-35 degrees

Celsius.

25.Do not wash the blades in water.

26.Only change comb attachments when the device is switched off.

PRODUCT DESCRIPTION:

1. Blade Head 2. Cutting Length level 3. Power Switch

4. LCD Display 5. Battery Remaining Capacity 6. Charge Indicator

7. Charging Socket 8a. Combs 8b. Oil bottle 8c, Charger / Charging cable

CHARGING THE BATTERY:

To begin charging plug the power cord into the charging Socket (6) or charging base, and the charger into a 220-240V~ 50/60Hz mains

power outlet.

Once plugged or put on a powered stand, the charging indicator icon (6) will light up and the remaining battery (5) will start blinking

from bottom to top and back again showing the loaded time remaining.

After the battery is fully charged the remaining power indicator will stop blinking unplug the device from the charger.

The charging time is about 3 hours.

POWER BUTTON / SAFETY LOCK (4)

Flick the power switch (4) to turn it on or off

OILING INDICATION (5a)

When the oiling indicator turns on. Oil the device/

USING THE CLIPPER

Select the desired cutting length by turning the cutting length lever (2).

To change the comb turn the clipper off, unclip the comb and clip on the right one. The combs have magnets, please make sure the

blade and the inside of the comb are aligned correcty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Adler AD 2831 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info