Bedienungsanleitung Adler AD 4127 (Seite 5 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

799958

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

2. Try to assemble and disassemble the unit for a few times before start working with the units.

ASSEMBLING THE DEVICE

3. The cover (8) with the feeder (2), juice and pulp separating bowl (10), pulp container (3) and juice jar are dishwasher safe.

4. Wipe the motor base (6) with a damp cloth.

5. Do not soak the stainless steel grater and filter sieve (9) in bleach.

4. Insert the large pulp container (3) correctly, place the juice jug on the opposite side of the juicer. NOTE: Before turning the device on,

make sure that all parts are properly installed.

NOTE: The machine is fitted with a safety switch (12). It prevents the juicer from being started unintentionally.

USE

- Be careful not to touch the sharp teeth on the bottom of the sieve.

- Make sure that the sieve sits properly on its base, so that the gear on the bottom of the sieve bowl engages the gear in the base.

- Make sure the juice jug is placed under the spout (7).

5. With the engine running, place the fruit (or vegetables) in the feeder (2). Use the pusher (1) to push them down. To get as much juice

as possible, push the fruit slowly.

2. Remove the cover (8).

4. Put the plug into the power socket and turn on the device by setting the switch to the '1' or '2' position. Depending on the fruit or

vegetables used, use the speed switch (5) to change the speed to low (switch in '1' position) or high (switch in '2' position).

CLEANING AND MAINTENANCE

- Make sure that the stainless steel filter (9) has been thoroughly washed.

1. Place the juicer on a smooth, flat and stable surface.

3. Remove the juice and pulp separating bowl (10), then pull the stainless steel grater and filter basket (9) upwards.

2. Install the stainless steel grater and filter sieve (9) and then put the cover on (8).

3. Make sure the juicer is assembled correctly.

6. Juice will start to drain into the jug and the pulp will start to collect in the container on the other side. To empty the pulp container (3),

switch off the juicer. Do not empty the container when the device is running and be careful not to overfill it, it may damage the device.

DISASSEMBLY OF THE DEVICE

2. Wash the fruit or vegetables you want to use. In case they do not fit in the feeder (2), cut them into smaller pieces.

- Make sure that the grater and filter sieve are not too loose on the base and that they rotate evenly.

1. Turn the 3 position switch (5) to the '0' position. Unplug the power cord of the juicer from the power socket. Release the safety handle

(11).

1. Place the juice and pulp separating bowl (10) on the base (6).

1. For easy cleaning - immediately after each use rinse removable parts under running water (to remove wet pulp). Allow parts to dry.

2. After disassembling the unit all removable parts may be washed in hot soapy water.

3. Close the safety locking handle (11).

Maximum operation time: 3min - 20 minutes break

6. Always treat the filter (9) with care as it can be easily damaged.

9. Do not use abrasive pads or aggressive agents for cleaning.

Two speeds mode: Hi - switch in position '2', Low - switch in position '1'.

Voltage: 220-240V ~ 50/60Hz

7. Discoloration of the plastic may occur with strongly colored fruit and vegetables. To help prevent this, wash parts immediately after

use.

TECHNICAL DATA

Maximum power: 2000W

8. If discoloration does occur, the plastic parts can be soaked in 10% lemon juice and water or they can be cleaned with a non-abrasive

cleaner. To assist with cleaning soak the stainless steel grater and filter sieve (9) in hot soapy water for approximately 10 minutes

immediately after juicing is completed. If pulp is left to dry on the filter it may clog the fine pores of the filter mesh thereby lessening the

effectiveness of the juicer.

NOTE: Never immerse the motor part in water or rinse under the tap.

Nominal power: 1000W

ingredients may pose a threat to the environment. The electrical device should be handed over to limit

its reuse and use. If in the device there are batteries you have to take out and give to the point stored separately.

Worn device should be returned to the appropriate point storage because it is dangerous in the device

Please transfer cardboard packaging to waste paper. Pour the polyethylene bags (PE) into the plastic container

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Adler AD 4127 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info