734431

Adler AD 7723 Seite 6

6
Zoom out
Zoom in
Vorherige Seite
1/72
Nächste Seite
6
23. Do not connect the fan heater to the automatic switching device, for example
temperature controlling device or time switch.
24. Flammable materials, for example furniture, bedclothes, paper, clothes, curtains should
be kept at least one meter from the fan heater.
20. Always turn the fan heater off and set the thermostat dial to minimum before removin
the power plug from the socket.
19. Place the fan heater only on flat, stable surface
pools etc. The humidity can cause short circuit, and effect in damaging the device.
22. The operating fan heater needs to be under supervision and in sight all the time. If you
are leaving the room with the fan heater, always turn the fan heater off. If the fan heater is
not used, the power plug has to be removed from the power outlet.
21. Never use the fan heater in high humidity rooms – bathroom, shower room, swimming
SAFERTY PROTECTION
WARNING: During use, do not touch or cover the air inlet and air outlet.
1.OVERHEAT PROTECTION This device is protected with an overheat protection that switches off the device automatically in case of
overheat, e.g. due to the total or partial obstruction of the grids (6). In this case, unplug the appliance, wait about 30 minutes for it to cool
and remove the object which is obstructing the grids. Then switch it back on as described above. The device should operate normally.
Should the problem persist, please contact authorized customer service.
To use the device with the remote control (8) supplied, remove the small battery compartment located at the base of the remote control. To
remove the battery compartment, simply squeeze the small tab and pull. Insert 1 x CR2025 (3V) lithium battery into the small crevice as
illustrated (picture 3).
1. Make sure the device is not hot.
CLEANING AND MAINTENANCE
3. Keep the air inlet and outlet openings clean. Do not allow dust to collect on the openings. To clean the air filter:
Remote control (8) operation is same as manual operation of buttons on control panel.
2. Before cleaning the device remove the plug from the electrical socket.
2.TIP-OVER PROTECTION This device is protected with a safety switch that turns off the device automatically when the device falls over,
or is at an excessive angle from the horizontal. This helps prevent accidents, and the device will back to the standby mode when it is put
back upright, press the buttons (A) on control panel or remote control to reset the device.
IMPORTANT: The + symbol on the battery inserted should be facing upwards. Firmly close the battery compartment to begin using the
Remote Control (8).
USE
ROOM TEMPERATURE ADJUST: Pressing buttons (E or F) will increase or decrease the desired room temperature. After setting desired
temperature the heater in device will switch on or switch off to maintain the desired room temperature. Device enables for temperature
setting from 10-35 degree Celsius. When the room temperature lower by 4℃ than the settled temperature of unit, device starts to heat on
high power automatically. Then when the room temperature lower by 2℃, the device start to heat on lower power automatically. If room
temperature reach the setting temperature level, the heating is stopped, the fan is permanently work on till room temperature lower than
the setting temperature by 2℃, the unit automatically return to lower power heating.
should be in a place that children and animals do not have access to.
TIMER: Pressing button (D) will set the timer from 1 hour increments up to 8 hours. After the set time the device will power off.
25. Do not cover the device or put any objects on it while it is operating. Do not use the
OSCILLATION: Pressing button (C) will set the device to turn on the base (4) from left to right, totally 45 degree.
LOW HEAT/HIGH HEAT: Pressing button (B) will switch between power levels:
• Low Heat = 1000W
• High Heat = 2000W
26. The power cord should not be placed above the fan heater, and it should not touch or
29. Some parts inside the device can be hot or cause sparking. Do not use the fan heater in
POWER SWITCH (5): Pressing it to switch on the device and press it again to switch off the device from supply.
POWER BUTTON (A): Pressing it will power on or off the device from Standby mode.
28. The device is not intended to be installed or used in vehicles.
the power outlet.
device to dry clothes.
27. The heating surfaces can heat to a temperature of 60 °C or higher. The fan heater
PRODUCT DESCRIPTION: CERAMIC FAN HEATER WITH REMOTE CONTROL (picture 1 & 2)
1. Control Panel 2. Digital Display 3. Heat Outlet 4. Base
D. Timer button E., F. Room temperature adjustment + / - buttons
A. Power button B. Low / High heat power button C. Oscillation button
be placed near hot surfaces of the fan heater. Do not place the fan heater directly under
5. Power Switch 6. Air inlet grid with dust mesh filter 7. Tip over Switch (Located on the Base)
8. Remote Control:
places, where gasoline, paints or other flammable materials are used or stored.
… 6 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

adler-ad-7723

Suche zurücksetzen

  • an meinem gerät fehlt der schalter produktbeschreibung 7
    Eingereicht am 12-2-2021 20:11

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Adler AD 7723 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info