Bedienungsanleitung Adler AD 7726 (Seite 6 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

800025

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

temperature controlling device or time switch.

20. Flammable materials, for example furniture, bedclothes, paper, clothes, curtains should

be kept at least one meter from the device.

21. Do not cover the device or put any objects on it while it is operating. Do not use the

device to dry clothes.

22.The heating surfaces can heat to a temperature of 60 °C or higher. The device should be

in a place that children and animals do not have access to.

23.The device is not intended to be installed or used in vehicles.

24. Some parts inside the device can be hot or cause sparking. Do not use the device in

places, where gasoline, paints or other flammable materials are used or stored.

25. The device must not be located immediately below a socket-outlet.

Before first use

The device should be used in wall sockets in a vertical position only, and not horizontally (lying).

WARNING: Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless

constant supervision is provided.

Device description:

1. Power switch 2. Fan speed butto 3.A. Temperature DOWN button

3.B. Temperature UP button 4. Timer button 5. Air inlet

6. Plug 7. Air outlet 8. Digital display

Instruction Manual

1. Plug device into 220-240V power supply outlet.

2. Press the power switch (1) on side of the unit to position “I” to turn on the device. Default device setting is: temperature 25 degree of

Celsius and high fan speed (HH).

3. Select your desired temperature by pressing “+” button (3.B.) to raise temperature or “-“ button (3.A.) to lower the temperature between

15-35 degree of Celsius on digital display. Pressing the button once changes one degree Celsius.

4. Select your desired fan speed by pressing button (2) to choice between high (HH) or low (LL) fan speed.

At “LL” low fan speed the operation is like below:

- If your desired temperature shown at digital display (8) is higher than present room temperature the heating element will heat the air at low

speed of fan,

- If you desired temperature shown at digital display (8) become lower than present room temperature the heating element stops air

heating, but fan will continue to blow the air at low speed.

At “HH” high fan speed the operation is like below:

- If your desired temperature shown at digital display (8) is higher than present room temperature the heating element will heat the air at

high speed of fan,

- If you desired temperature shown at digital display (8) become lower than present room temperature the heating element stops air

heating, but fan will continue to blow the air at high speed.

5.To change temperature unit from Celsius to Fahrenheit scale button (2) for a few seconds. To come back from Fahrenheit to Celsius press

button (2) for a few seconds again.

6. To stop operation, turn the power switch (1) to “0” position and unplug the device from power outlet.

NOTE: If you do not set the timer, the digital display (8) always shows default setting temperature (25℃) or desired temperature set up by

you.

Setting the timer

The device has a built-in timer that will automatically turn the device off after a set amount of time.

1. While the unit is plugged in and turned on, press the Timer button (4) to active the function of timer.

2. Press Timer button (4) again to set desired number of hours. You can choose between 1-12 hours.

3. Once desired number of hours have been chosen, the display will flashing twice. The device will automatically turn off after desired

amount of time passed.

4. To cancel timer settings, turn the device off or press the timer button until the display shows “00”.

The digital display shows the temperature set by the user, and if additionally the timer was previously set, the display shows the desired

temperature and the set time alternately.

OVERHEAT PROTECTION SYSTEM

The device is provided with a safety system that automatically cuts the power to the heater in the event of overheating. If this event occurs,

switch the device off, remove the plug from the power outlet and wait until the device has cooled down (after about 10 minutes).

CLEANING AND MAINTENANCE

Make sure the device is not hot. Remove the plug from the socket before cleaning. Keep the inlet and outlet openings clean. Do not allow

dust to settle on them. Use a dry or slightly damp cloth to clean housing. Do not immerse the device in water. Store the device in a cool, dry

place until next use.

TECHNICAL DATA

Voltage: 220-240V~ 50Hz

Power: 400W

Max power: 1500W To protect your environment: please separate carton boxes and plastic bags and dispose them in

corresponding waste bins. Used appliance should be delivered to the dedicated collecting points due

to hazarsous components, which may effect the environment. Do not dispose this appliance in the

common waste bin.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Adler AD 7726 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info