Bedienungsanleitung Adler AD 7730 (Seite 9 von 148) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

800029

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

MONTAGE

The base (10) montage: Align the four fixing screw holes of the base (10) with the screw posts of the base (10), and screw with four self-

tapping screws to put the product into use. Look at figure 2.

PRODUCT DESCRIPTION (Figure 1)

1.Humidifed air outlet 2.Front display panel

3.Air outlet 4.Housing

5.Air inlet 6.Back cover

7.Drain cover 8.Top panels

9. Drain plug 10.The base

11.Remote control 12. Power switch

TOP PANEL & FRONT PANEL & REMOTE CONTROL MARKING – Figure 3

A. Standby button A1. Fan function indicator

B. Timer button B1.Timer indicator B2.Timer / Temperature / Cooling down count down indicator

C. Timer / Temperature increase button D. Timer / Temperature decrease button

E. Heating level regulation button E1. Low heating level indicator E2. High heating level indicator

F. Oscillation button G. Humidifier function button G1. Humidifier indicator

H. Temperature unit indicator

USAGE

1. Power on: Place the device on a stable floor and insert the plug into socket. Turn on the power switch (12) on the back of the product. “I”

means switched on, “0” means off. At this time, the device is in standby mode, the display shows ambient temperature (B2), and the

temperature unit indicator (H) will light on.

2. Fan

Press the button (A), the indicator (A1) will light up and the fan is operating (flow the air in room temperature).

3. Heating

Press the button (E) once for low-level heating ~ 1500W, the display lights up indicator (E1).

Press the button (E) twice for high-level heating 2200W, the display will light both indicators (E1 + E2).

Press the button (E) again to cancel the heating.

TIMER function: Press the button (B) repeatedly to set a period after which the device will turn itself off (between 1.0 hour – 12.0 hours, in

steps of 60 minutes). At the same time timer indicator (B1) light display.

OSCILLATION function: Press button (F) to activate oscillation, the device will swing to the right and left to distribute the exhaust air evenly.

Press again button (F) to cancel oscillation function.

TEMPERATURE ADJUSTMENT

Adjust room temperature by pressing button (D) or (C). The default setting temperature is 25°C. Temperature range from 10-35°C. Pres the

button (D) to increase the desired temperature and press the button (C) to decrease the desired temperature. The device is intelligently

programmed, it selects the working level between low or high heat according to the desired temperature and present ambient temperature.

HUMIDIFICATION FUNCTION

At first pour the water to water tank (13) according to instruction described below. To pour the water to water tank (13), unplug the device at

first. Next press down and pull outside the protrude part on the back cover (6) - look at figure 4. Take out the water tank (13) from the housing,

unscrew the plug of water tank (13) counterclockwise, pour clean water (no essential oils added) and screw the plug tightly. Put the water tank

(13) inside the housing. Set the cover properly on two latches places well and push it to close.

The humidifying function can be used normally. Plug in the device.

Press the button (G), the product turns on the humidification function, the humidification indicator (G1) lights up. Press the button (G) again to

turn off the humidification function, at the same time the humidification indicator (G1) will be off. The humidification function can also be used

separately when fan / heating function is switch off but power is on.

To drain the water out open the drain cover (7) pull the drain plug (9) and drain the reminding water to suitable tank.

When the device is not used for a long time, the water in the tank should be drained.

Applicable environment conditions for the device operation:

- heating function use temperature in range from -20°C to 25°C.

- humidifier function use in temperature in range from 5°C to 40°C and the relative humidity less than 80%.

To turn off the device press the button (A) again. Then, the fan will cool down the heating element inside the housing during 30 seconds, next

the fan will automatic turn off. If the device is not set on heating function before, it will go directly to standby.

Lighting off of the front display panel (2): After the device is working for 10 minutes, it will automatically enter the light off screen mode, press

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Adler AD 7730 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info