Bedienungsanleitung Adler AD 7809 (Seite 6 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Finnisch)

734434

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

23. If disposing of the heater please follow rules of oil disposal.

1. Diode indicating operation of the device

18. Do not cover the heater with curtains, a towel or hang washing on it – this can damage

the heater or cause a fire.

3. Power level control knob 0/1/2/3

6. Ribs

19. When using the heater, completely unwind its cable and make sure that the cable is not

touching the hot surface of the heater.

20. Do not use the heater near basins, showers, sinks, pools or other places where it can

get wet.

ASSEMBLY (Fig. 2)

1. Turn the heater upside down.

4. Cable storage

2. Place the wheel bases between the last ribs.

16. The power cable should not be placed above the heater, and also should not touch or

lie close to hot surfaces. Do not place the heater under an electrical outlet.

sink filled with water.

4. Block the clamp by screwing on the butterfly nut.

WARNING: To avoid overheating do not cover the heater.

3. Use the U-shaped clamp to hook the bases.

5. Place the heater on the wheels.

17. The surface of the heater can heat up to high temperatures of over 60 degrees C. Take

care when near the heater.

DESCRIPTION OF THE DEVICE (Fig. 1)

2. Thermostat control knob

15. The heater should be placed on a level, heat-resistant surface, away (at least one

meter) from flammable materials (lace curtains, curtains, wallpaper, furniture etc.).

21. The device must be completely cool prior to storage. Keep the original packaging to

store the heater in during non-heating seasons.

CAUTION: After turning the heater, wait at least one hour before connecting it to a power outlet.

5. Wheels

USING THE DEVICE

22. The heater is filled with a set amount of special oil. Repairs requiring opening of the oil

container must be carried out only by the manufacturer or authorized representative, who

should be contacted if oil leaks from the heater.

CLEANING THE DEVICE

1. Prior to cleaning always remove the plug from the electrical outlet.

4. Never use wax, shining agents or chemical agents to clean the heater. They may react with the device and cause discoloration or

even damage.

1. Place the oil heater a minimum of 100 cm from walls, furniture, curtains, plants etc.

3. Turn the heater on by turning the on-switch control knob (3) to position 1 (low heating power) or 2,3 (high heating power). Set a

comfortable oil heater temperature by turning the thermostat control knob.

CAUTION: During first use of the heater a small amount of smoke may appear. This is normal.

3. Wipe the heater with a damp cloth, then wipe dry.

2. Make sure that the on-switch control knob (3) and thermostat control knob (2) are set to '0'. Connect the oil heater to mains power.

2. Prior to cleaning allow the heater to cool. Make sure that it is cool.

4. After you finish using the heater, turn it off by turning the on-switch control knob and thermostat control knob to '0' and disconnect the

power cable from mains power.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Adler AD 7809 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info